View ATAR092-C_2757163.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

features ? extended temperature range for high temperature up to 105c 4-kbyte rom, 256 4-bit ram 16 bi-directional i/os up to 7 external/inter nal interrupt sources multifunction timer/counter with ? ir remote control carrier generator ? bi-phase, manchester and pulse- width modulator and demodulator ? phase control function programmable system clock with prescal er and five different clock sources wide supply-voltage range (1.8v to 6.5v) very low sleep current (< 1 a) 32 16-bit eeprom (atar892-c only) synchronous serial interface (2-wire, 3-wire) watchdog, por and brown-out function voltage monitoring inclusive lo_bat detect flash controller atam893 available (sso20) 1. description the ATAR092-C and atar892-c are members of atmel?s family of 4-bit single-chip microcontrollers. they offer the highest int egration for ir and rf data communication, remote-control and phase-control applications. the ATAR092-C and atar892-c are suitable as transmitters as well as receiv ers. they contain ro m, ram, parallel i/o ports, two 8-bit programmable multifunction timer/counters with modulator and demodulator function, voltage supervision, in terval timer with wa tchdog function and a sophisticated on-chip clock generation with external clock input, integrated rc-, 32-khz crystal- and 4-mhz crystal-osci llators. the atar892-c has an additional eeprom as a second ch ip in one package. figure 1-1. block diagram vdd t2i sd voltage monitor external input marc4 utcm osc1 osc2 i/o bus rom ram 4-bit cpu core 256 x 4 bit vss data direction + alternate function data direction + interrupt control port 4 port 5 data direction + alternate function port 6 timer 3 brown-out protect. reset clock management timer 1 watchdog timer timer 2 serial interface port 1 p o r t 2 d a t a d i r e c t i o n t2o sd sc t3o t3i bp10 bp13 bp20/nte bp21 bp22 bp23 bp40 int3 sc bp41 vmi bp42 t2o bp43 int3 bp50 int6 bp51 int6 bp52 int1 bp53 int1 bp60 t3o bp63 t3i rc oscillators crystal oscillators 4 k x 8 bit vmi with modulator ssi external clock input interval- and 8/12-bit timer 8-bit timer/counter with modulator and demodulator t2i low-current microcontroller for wireless communication ATAR092-C atar892-c 4593d?4bmcu?05/06
2 4593d?4bmcu?05/06 ATAR092-C/atar892-c 2. pin configuration figure 2-1. pinning sso20 vdd bp40/int3/sc bp53/int1 bp52/int1 bp51/int6 bp50/int6 osc1 osc2 bp60/t3o bp10 vss bp43/int3/sd bp42/t2o bp41/vmi/t2i bp23 bp22 bp21 bp20/nte bp63/t3i bp13 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 table 2-1. pin description name type function alternate function pin no. reset state vdd ? supply voltage ? 1 na vss ? circuit ground ? 20 na bp10 i/o bi-directional i/o line of port 1.0 ? 10 input bp13 i/o bi-directional i/o line of port 1.3 ? 11 input bp20 i/o bi-directional i/o line of port 2.0 nte-tes t mode enable, see section ?master reset? 13 input bp21 i/o bi-directional i/o line of port 2.1 ? 14 input bp22 i/o bi-directional i/o line of port 2.2 ? 15 input bp23 i/o bi-directional i/o line of port 2.3 ? 16 input bp40 i/o bi-directional i/o line of port 4.0 sc-serial clock or int3 external interrupt input 2 input bp41 i/o bi-directional i/o line of port 4.1 vmi voltage monitor input or t2i external clock input timer 2 17 input bp42 i/o bi-directional i/o line of port 4.2 t2o timer 2 output 18 input bp43 i/o bi-directional i/o line of port 4.3 sd serial data i/o or int3-external interrupt input 19 input bp50 i/o bi-directional i/o line of port 5.0 int6 external interrupt input 6 input bp51 i/o bi-directional i/o line of port 5.1 int6 external interrupt input 5 input bp52 i/o bi-directional i/o line of port 5.2 int1 external interrupt input 4 input bp53 i/o bi-directional i/o line of port 5.3 int1 external interrupt input 3 input bp60 i/o bi-directional i/o line of port 6.0 t3o timer 3 output 9 input bp63 i/o bi-directional i/o line of port 6.3 t3i timer 3 input 12 input osc1 i oscillator input 4-mhz crystal input or 32-khz crystal input or external clock input or external trimming resistor input 7 input osc2 o oscillator output 4-mhz crystal output or 32-khz crystal output or external clock input 8na
3 4593d?4bmcu?05/06 ATAR092-C/atar892-c 3. introduction the ATAR092-C/atar892-c are members of atmel?s family of 4-bit single-chip microcontrol- lers. they contain rom, ram, parallel i/o ports, two 8-bit programmable multi-function timer/counters, voltage supervis ion, interval timer with watchdog function, a sophisticated on-chip clock generation with integrated rc-, 32-khz crystal- and 4-mhz crystal oscillators. 4. marc4 architecture 4.1 general description the marc4 microcontroller consists of an advanced stack-based, 4-bit cpu core and on-chip peripherals. the cpu is based on the harvard architecture with physically separate program memory (rom) and data memory (ram). three independent buses, the instruction bus, the memory bus and the i/o bus, are used for parallel communication between rom, ram and peripherals. this enhances program execution sp eed by allowing both instruction prefetching, and a simultaneous communication to the on-chip peripheral circuitry. the extremely powerful integrated interrupt controller with associated eight prioritized interrupt levels supports fast and efficient processing of hardware events. the ma rc4 is designed for the high-level programming language qforth. the core includes both an expre ssion and a return stack. this architecture enables high-level language programming without any loss of efficiency or code density. figure 4-1. marc4 core table 3-1. available variants of ataxx9x version type rom e2prom peripheral packages flash device atam893 4-kbyte eeprom 64 byte sso20 production ATAR092-C 4-kbyte mask rom ? sso20 production atar892-c 4-kb yte mask rom 64 byte sso20 instruction decoder ccr tos alu ram rp x y program 256 x 4-bit marc4 core clock reset sleep memory bus i/o bus instruction bus reset system clock interrupt controller on-chip peripheral modules memory sp pc
4 4593d?4bmcu?05/06 ATAR092-C/atar892-c 4.2 components of marc4 core the core contains rom, ram, alu, a program counter, ram address registers, an instruction decoder and an interrupt controller. the following sections describe each functional block in more detail. 4.2.1 rom the program memory (rom) is mask programmed with the customer application program dur- ing the fabrication of the microcontroller. the 4 kbyte rom size is addressed by a 12-bit wide program counter. an additional 1 kbyte of rom exists which is reserved for quality control self-test software. the lowest user rom address segment is taken up by a 512-byte zero page which contains predefined start addresses for inte rrupt service routines and special subroutines accessible with single byte instructions (scall). the corresponding memory map is shown in figure 4-2 . look-up tables of constants can also be held in rom and are accessed via the marc4?s built-in table instruction. figure 4-2. rom map 4.2.2 ram the ATAR092-C and atar892-c contain 256 4-bit wide static random access memory (ram). it is used for the expression stack, the return stack and data me mory for variables and arrays. the ram is addressed by any of the fo ur 8-bit wide ram address registers sp, rp, x and y. 4.2.2.1 expression stack the 4-bit wide expression stack is addressed with the expression stack pointer (sp). all arith- metic, i/o and memory reference operations take their operands from, and return their results to the expression stack. the marc4 performs the operations with the top of stack items (tos and tos-1). the tos register contains the top elem ent of the expression stack and works in the same way as an accumulator. this stack is also used for passing parameters between subrou- tines and as a scratch pad area for temporary storage of data. rom (4 k x 8 bit) zero page fffh 7ffh 1ffh 000h 1f0h 1f8h 010h 018h 000h 008h 020h 1e8h 1e0h scall addresses 140h 180h 040h 0c0h 008h $autosleep $reset int0 int1 int2 int3 int4 int5 int6 int7 1e0h 1c0h 100h 080h page 000h zero
5 4593d?4bmcu?05/06 ATAR092-C/atar892-c 4.2.2.2 return stack the 12-bit wide return stack is addressed by the return stack pointer (rp). it is used for storing return addresses of subroutines, interrupt routines and for keeping loop index counts. the return stack can also be used as a temporary storage area. the marc4 instruction set supports the exchange of data between the top elements of the expression stack and the return stack. the two stacks within the ram have a user definable location and maximum depth. figure 4-3. ram map 4.2.3 registers the marc4 controller has seven programmable registers and one condition code register. they are shown in the following programming model ( figure 4-4 on page 6 ). 4.2.3.1 program counter (pc) the program counter is a 12-bit register which contains the address of the next instruction to be fetched from rom. instructions currently being executed are decoded in the instruction decoder to determine the internal micro-operations. for linear code (no calls or branches) the program counter is incremented with every instruction cycle. if a branch-, call-, return-instruction or an interrupt is executed, the program counter is loaded with a new address. the program counter is also used with the table instruction to fetch 8-bit wide rom constants. ram fch 00h autosleep ffh 03h 04h x y sp rp tos-1 expression stack return stack global variables ram address registers: 07h (256 x 4-bit) global variables 4-bit tos tos-1 tos-2 30 sp expression stack return stack 0 11 12-bit rp v
6 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 4-4. programming model 4.2.3.2 ram address registers the ram is addressed with four 8-bit wide ram address registers: sp, rp, x and y. these reg- isters allow access to any of the 256 ram nibbles. 4.2.3.3 expression stack pointer (sp) the stack pointer contains the address of the next-to-top 4-bit item (tos-1) of the expression stack. the pointer is automatically pre-incr emented if a nibble is moved onto the stack or post-decremented if a nibble is removed from the stack. every post-decrement operation moves the item (tos-1) to the tos register before the sp is decremented. after a reset the stack pointer has to be initialized with >sp s0 to allocate the start address of the expression stack area. 4.2.3.4 return stack pointer (rp) the return stack pointer points to the top element of the 12-bit wide return stack. the pointer automatically pre-increments if an element is mov ed onto the stack, or it post-decrements if an element is removed from the stack. the return stack pointer increments and decrements in steps of 4. this means that every time a 12-bit element is stacked, a 4-bit ram location is left unwritten. this location is used by the qforth compiler to allocate 4-bit variables. after a reset the return stack pointer has to be initialized via > rp fch. 4.2.3.5 ram address registers (x and y) the x and y registers are used to address any 4-bi t item in ram. a fetch operation moves the addressed nibble onto the tos. a store operation moves the tos to the addressed ram loca- tion. by using either the pre-increment or post-decrement addressing mode, arrays located in ram can be compared, filled or moved tos ccr 0 3 0 3 0 7 0 7 7 0 11 rp sp x y pc -- b i program counter return stack pointer expression stack pointer ram address register (x) ram address register (y) top of stack register condition code register carry/borrow branch interrupt enable reserved 0 7 c 0 0 0
7 4593d?4bmcu?05/06 ATAR092-C/atar892-c 4.2.3.6 top of stack (tos) the top of stack register is the accumulator of the marc4. all arithmetic/logic, memory refer- ence and i/o operations use this register. the tos register receives data from the alu, rom, ram or i/o bus. 4.2.3.7 condition code register (ccr) the 4-bit wide condition code register contains the branch, the carry and the interrupt enable flag. these bits indicate the current state of the cpu. the ccr flags are set or reset by alu operations. the instructions set_bcf, tog_bf, cc r! and di allow direct manipulation of the condition code register. 4.2.3.8 carry/borrow (c) the carry/borrow flag indicates that the borrowing or carrying out of arithmetic logic unit (alu) occurred during the last arithmetic operation. during shift and rotate operations, this bit is used as a fifth bit. boolean operations have no affect on the c-flag. 4.2.3.9 branch (b) the branch flag controls conditional program branching. should the branch flag have been set by a previous instru ction, a conditional br anch will cause a ju mp. this flag is affected by arith- metic, logic, shift, and rotate operations. 4.2.3.10 interrupt enable (i) the interrupt enable flag globally enables or disables the triggering of all interrupt routines with the exception of the non-maskable reset. after a re set or while executing the di instruction, the interrupt enable flag is reset, thus disabling a ll interrupts. the core will not accept any further interrupt requests until the interrupt enable flag has been set again by either executing an ei or sleep instruction. 4.2.4 alu the 4-bit alu performs all the arithmetic, logical, shift and rotate operations with the top two ele- ments of the expression stack (tos and tos-1) and returns the result to the tos. the alu operations affect the carry/borrow and branch flag in the condition code register (ccr). figure 4-5. alu zero-address operations tos-1 ccr ram tos-2 sp tos-3 tos alu tos-4
8 4593d?4bmcu?05/06 ATAR092-C/atar892-c 4.2.5 i/o bus the i/o ports and the registers of the peripheral modules are i/o mapped. all communication between the core and the on-chip peripherals ta kes place via the i/o bus and the associated i/o control. with the marc4 in and out instructions the i/o bus allows a direct read or write access to one of the 16 primary i/o addresses. more about the i/o access to the on-chip periph- erals is described in the section ?peripheral modules?. the i/o bus is internal and is not accessible by the customer on the final microcontro ller device, but it is used as the interface for the marc4 emulation (see also the section ?emulation?). 4.2.6 instruction set the marc4 instruction set is optimized for the high level programming language qforth. many marc4 instructions are qforth words. this enables the compiler to generate a fast and compact program code. the cpu has an instruction pipeline allowing the controller to prefetch an instruction from rom at the same time as the present instruction is being executed. the marc4 is a zero-address machine, the instructi ons contain only the operation to be performed and no source or destination address fields. the operations are implicitly performed on the data placed on the stack. there are one and two byte in structions which are executed within 1 to 4 machine cycles. a marc4 machine cycle is made up of two s ystem clock cycl es (syscl). most of the instructions are only one byte long and are executed in a single machine cycle. for more information refer to the ?m arc4 programmer?s guide?. 4.2.7 interrupt structure the marc4 can handle interrupts with eight different priority levels. they can be generated from the internal and external interrupt sources or by a software interrupt from the cpu itself. each interrupt level has a hard-wired priority and an associated vector for the service routine in the rom (see table 3-1 on page 3 ). the programmer can postpone the processing of interrupts by resetting the interrupt enable flag (i) in the ccr. an interru pt occurrence will still be regis- tered, but the interrupt routine only started after the i flag is set. all interrupts can be masked, and the priority individually software configured by programming the appropriate control register of the interrupting module (see section ?peripheral modules?). 4.2.7.1 interrupt processing for processing the eight interrupt levels, the marc4 includes an interrupt controller with two 8-bit wide interrupt pending and interrupt active registers. the interrupt controller samples all interrupt requests during every non-i/o instruction cycle and latches these in the interrupt pend- ing register. if no higher priority interrupt is present in the interrupt active register, it signals the cpu to interrupt the current program execution. if the interrupt enable bit is set, the processor enters an interrupt acknowledge cycle. during this cycle a short ca ll (scall) instruction to the service routine is executed and the curr ent pc is saved on the return stack. an interrupt service routine is co mpleted with the rti in struction. this instru ction resets the cor- responding bits in the interrupt pending/active register and fetches the return address from the return stack to the program counter. when the interrupt enable flag is reset (triggering of inter- rupt routines are disabled), the execution of new interrupt service routines is inhibited but not the logging of the interrupt requests in the interrupt pending register. the execution of the interrupt is delayed until the interrupt enable flag is set agai n. note that interrupts are only lost if an inter- rupt request occurs while the co rresponding bit in th e pending register is still set (i.e., the interrupt service routine is not yet finished).
9 4593d?4bmcu?05/06 ATAR092-C/atar892-c 4.2.7.2 interrupt latency the interrupt latency is the time from the occurrence of the interrupt to the interrupt service rou- tine being activated. in marc4 this is extremely short (taking between 3 to 5 machine cycles depending on the state of the core). figure 4-6. interrupt handling 7 6 5 4 3 2 1 0 priority level int5 active int7 active int2 pending swi0 int2 active int0 pending int0 active int2 rti rti int5 int3 active int3 rti rti rti int7 time main/ autosleep main/ autosleep table 4-1. interrupt priority table interrupt priority rom address interrupt opcode function int0 lowest 040h c8h (scall 040h) software interrupt (swi0) int1 | 080h d0h (scall 080h) external hardware interrupt, any edge at bp52 or bp53 int2 | 0c0h d8h (scall 0c0h) timer 1 interrupt int3 | 100h e8h (scall 100h) ssi interrupt or external hardware interrupt at bp40 or bp43 int4 | 140h e8h (scall 140h) timer 2 interrupt int5 | 180h f0h (scall 180h) timer 3 interrupt int6 1c0h f8h (scall 1c0h) external hardware interrupt, at any edge at bp50 or bp51 int7 highest 1e0h fch (scall 1e0h) voltage monitor (vm) interrupt
10 4593d?4bmcu?05/06 ATAR092-C/atar892-c 4.2.7.3 software interrupts the programmer can generate interrupts by using the software interrupt instruction (swi) which is supported in qforth by predefined macros named swi0...swi7. the software triggered interrupt operates exactly like any hardware triggered interrupt. the swi instruction takes the top two elements from the expression stack and writes the corresponding bits via the i/o bus to the interrupt pending register. therefore, by using the swi instruction, interrupts can be re-prior- itized or lower priority processes scheduled for later execution. 4.2.7.4 hardware interrupts in the ATAR092-C, there are eleven hardware inte rrupt sources with seven different levels. each source can be masked individually by mask bits in the corresponding control registers. an overview of the possible hardware configurations is shown in table 4-2 . 4.3 master reset the master reset forces the cpu into a well-defined condition. it is unmaskable and is activated independent of the current program state. it can be triggered by either initial supply power-up, a short collapse of the power supply, brown-out detection circuitry, watchdog time-out, or an exter- nal input clock supervisor stage (see figure 4-7 on page 11 ). a master reset activation will reset the interrupt enable flag, the interrupt pending register and the interrupt active register. during the power-on reset phase the i/o bus control signals are set to reset mode thereby initializing all on-chip peripherals. all bi-directional ports are set to input mode. attention: during any reset phase, the bp20/nte input is driven towards v dd by an additional internal strong pull-up transistor. this pin must not be pulled down to v ss during reset by any external circuitry representing a resistor of less than 150 k ? . releasing the reset results in a short call instruction (opcode c1h) to the rom address 008h. this activates the initialization routine $reset which in turn has to initialize all necessary ram variables, stack pointers and peripheral configuration registers (see table 5-1 on page 22 ). table 4-2. hardware interrupts interrupt interrupt mask interrupt source register bit int1 p5cr p52m1, p52m2 p53m1, p53m2 any edge at bp52 any edge at bp53 int2 t1m t1im timer 1 int3 sisc sim ssi buffer full/em pty or bp40/bp43 interrupt int4 t2cm t2im timer 2 compare match/overflow int5 t3cm1 t3cm2 t3c t3im1 t3im2 t3eim timer 3 compare register 1 match timer 3 compare register 2 match timer 3 edge event occurs (t3i) int6 p5cr p50m1, p50m2 p51m1, p51m2 any edge at bp50, any edge at bp51 int7 vcm vim external/internal voltage monitoring
11 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 4-7. reset configuration 4.3.1 power-on reset and brown-out detection the ATAR092-C/atar892-c have a fully integrated power-on reset and brown-out detection circuitry. for reset generation no external components are needed. these circuits ensure that the core is held in the reset state until the minimum operating supply voltage has been reached. a reset condition will also be generated should the supply voltage drop momentarily below the minimum operating le vel except when a power down mode is acti- vated (the core is in sleep mode and the peripheral clock is stopped). in this power-down mode the brown-out detection is disabled. two values for the brown-out voltage threshold are programmable via the bot bit in the sc register. a power-on reset pulse is generated by a v dd rise across the default bot voltage level (1.7v). a brown-out reset pulse is generated when v dd falls below the brown-out voltage threshold. two values for the brown-out voltage threshold are programmable via the bot bit in the sc register. when the controller runs in the upper supply voltage range with a high system clock frequency, the high threshold must be used. when it runs with a lower system clock frequency, the low threshold and a wider supply voltage range may be chosen. for further details, see the electrical specification and the sc register description for bot programming. reset timer v dd cl power-on reset internal reset res cl = syscl/4 brown-out detection watch- dog cwd res ext. clock supervisor exin pull-up nrst v dd v dd v ss v ss
12 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 4-8. brown-out detection 4.3.2 watchdog reset the watchdog?s function can be enabled at the wdc register and triggers a reset with every watchdog counter overflow. to suppress the watchdog reset, the watchdog counter must be regularly reset by reading the watchdog register address (cwd). the cpu reacts in exactly the same manner as a reset stimulus from any of the above sources. 4.3.3 external clock supervisor the external input clock supervisor function can be enabled if the external input clock is selected within the cm and sc registers of the clock m odule. the cpu reacts in exactly the same man- ner as a reset stimulus from any of the above sources. 4.4 voltage monitor the voltage monitor consists of a comparator with internal voltage reference. it is used to super- vise the supply voltage or an external voltage at the vmi pin. the comparator for the supply voltage has three internal programmable thresholds: one lower threshold (2.2v), one middle threshold (2.6v). and one higher threshold (3.0v). for external voltages at the vmi pin, the com- parator threshold is set to v bg = 1.3v. the vms bit indicates if the supervised voltage is below (vms = 0) or above (vms = 1) this threshold. an interrupt can be generated when the vms bit is set or reset to detect a rising or falling slope. a voltage monitor interrupt (int7) is enabled when the interrupt mask bit (vim) is reset in the vmc-register. v dd cpu reset t bot = 1 2.0 v 1.7 v cpu reset bot = 0 t d t d = 1.5 ms (typically) bot = 1, low brown-out voltage threshold 1.7 v (is reset value). bot = 0, high brown-out voltage threshold 2.0 v. t d t d
13 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 4-9. voltage monitor 4.4.1 voltage monitor control/status register vm2: v oltage monitor m ode bit 2 vm1: v oltage monitor m ode bit 1 vm0: v oltage monitor m ode bit 0 v dd vm2 voltage monitor vm1 vm0 vim vms - - res out in bp41/ vmi int7 vmc vmst primary register address: ?f?hex bit 3 bit 2 bit 1 bit 0 vmc: write vm2 vm1 vm0 vim reset value: 1111b vmst: read ? ? reserved vms reset value: xx11b table 4-3. voltage monitor modes vm2 vm1 vm0 function 1 1 1 disable voltage monitor 110 external (vim input), internal reference threshold (1.3 v), interrupt with negative slope 1 0 1 not allowed 100 external (vmi input), internal reference threshold (1.3 v), interrupt with positive slope 011 internal (supply voltage), high threshold (3.0 v), interrupt with negative slope 010 internal (supply voltage), middle threshold (2.6 v), interrupt with negative slope 001 internal (supply voltage), low threshold (2.2 v), interrupt with negative slope 0 0 0 not allowed
14 4593d?4bmcu?05/06 ATAR092-C/atar892-c vim v oltage i nterrupt m ask bit vim = 0, voltage monitor interrupt is enabled vim = 1, voltage monitor interrupt is disabled vms v oltage m onitor s tatus bit vms = 0, the voltage at the comparator input is below v ref vms = 1, the voltage at the comparator input is above v ref figure 4-10. internal supply voltage supervisor figure 4-11. external input voltage supervisor 4.5 clock generation 4.5.1 clock module the ATAR092-C/atar892-c contains a clock module with 4 different internal oscillator types: two rc-oscillators, one 4-mhz crystal oscillator and one 32-khz crystal oscillator. the pins osc1 and osc2 are the interface to connect a crystal either to the 4-mhz, or to the 32-khz crystal oscillator. osc1 can be us ed as input for external clocks or to connect an external trim- ming resistor for the rc-oscillator 2. all necessa ry circuitry except the crystal and the trimming resistor is integrated on-chip. one of these oscillator types or an external input clock can be selected to generate the system clock (syscl). in applications that do not require exact timing, it is possible to use the fully integrated rc-oscil- lator 1 without any external components. the rc-oscillator 1 center frequency tolerance is better than 50%. the rc-oscillator 2 is a trimmable os cillator whereby the oscillator frequency can be trimmed with an external resistor attached between osc1 and v dd . in this configuration, the rc-oscillator 2 frequency ca n be maintained in a stable state with a tolerance of 15% over the full operating temperature and voltage range. v dd low threshold middle threshold high threshold vms = 1 low threshold middle threshold high threshold vms = 0 3.0 v 2.6 v 2.2 v 1.3 v vmi vms = 1 vms = 0 positive slope negative slope vms = 1 vms = 0 interrupt negative slope interrupt positive slope internal reference level t
15 4593d?4bmcu?05/06 ATAR092-C/atar892-c the clock module is programmable via software with the clock management register (cm) and the system configuration register (sc). the required oscillator co nfiguration can be selected with the os1 bit and the os0 bit in the sc register . a programmable 4-bit divider stage allows the adjustment of the system clock speed. a specia l feature of the clock management is that an external oscillator may be used and switched on and off via a port pin for the po wer-down mode. before the external clock is switched off, the internal rc-oscillator 1 mu st be selected with the ccs bit and then the sleep mode may be activa ted. in this state an in terrupt can wa ke up the controller with the rc-oscillator, and the exte rnal oscillator can be activated and selected by software. a synchronization stage avoids too short clock periods if the clock source or the clock speed is changed. if an external input clock is selected, a supervisor circuit monitors the external input and generates a hardware reset if the external clock source fails or drops below 500 khz for more than 1 ms. figure 4-12. clock module the clock module generates two ou tput clocks. one is the system clock (syscl) and the other the periphery (subcl). the sysc l can supply the core and th e peripherals and the subcl can supply only the peripherals with clocks. the modes for clock sources are programmable with the os1 bit and os0 bit in the sc register and the ccs bit in the cm register. ext. clock exin exout stop rc oscillator2 rcout2 stop r trim 4-mhz oscillator 4out stop oscin oscout oscin oscout 32-khz oscillator 32out oscin oscout rc oscillator 1 rcout1 control stop in1 in2 cin /2 /2 /2 /2 divider sleep wdl osc-stop nstop ccs css1 css0 cm bot - - - os1 os0 subcl syscl sc * osc1 * osc2 * mask option cin/16 32 khz table 4-4. clock modes mode os1 os0 clock source for syscl clock source for subcl ccs = 1 ccs = 0 1 1 1 rc-oscillator 1 (internal) external input clock c in /16 2 0 1 rc-oscillator 1 (internal) rc-oscillator 2 with external trimming resistor c in /16 3 1 0 rc-oscillator 1 (internal) 4-mhz oscillator c in /16 4 0 0 rc-oscillator 1 (internal) 32-khz oscillator 32 khz
16 4593d?4bmcu?05/06 ATAR092-C/atar892-c 4.5.2 oscillator circuits and external clock input stage the ATAR092-C/atar892-c series co nsists of four different inte rnal oscillators: two rc-oscilla- tors, one 4-mhz crystal oscillator, one 32-khz crystal osc illator and one external clock input stage. 4.5.2.1 rc-oscillator 1 fully integrated for timing insensitive ap plications, it is possible to use t he fully integrated rc oscillator 1. it operates without an y external compone nts and saves additional cost s. the rc-oscillator 1 cen- ter frequency tolerance is better than 50% over the full temperature and voltage range. the basic center freq uency of the rc-oscillator 1 is f o 3.8 mhz. the rc oscillator 1 is selected by default after power-on reset. figure 4-13. rc-oscillator 1 4.5.2.2 external input clock the osc1 or osc2 (mask option) can be driven by an external clock source provided it meets the specified duty cycle, rise and fall times and input levels. additionally the external clock stage contains a supervisory circuit for the input clock. the supervisor function is controlled via os1, os0 bit in the sc register and the ccs bit in the cm register. if the external input clock is miss- ing for more than 1 ms and ccs = 0 is set in the cm register, the supervisory circuit generates a hardware reset. figure 4-14. external input clock rc-oscillator 1 rcout1 stop control rcout1 osc-stop ext. input clock exout stop ext. clock rcout1 osc-stop exin ccs res osc1 osc2 clock monitor ext. clock or
17 4593d?4bmcu?05/06 ATAR092-C/atar892-c 4.5.2.3 rc-oscillator 2 with external trimming resistor the rc-oscillator 2 is a high re solution trimmable oscillator wher eby the oscillator frequency can be trimmed with an external resistor between osc1 and v dd . in this configuration, the rc-oscil- lator 2 frequency can be maintained in a stable state with a tolerance of 10% over the full operating temperature range and stet voltage range v dd from 2.5v to 6.0v. for example: an output frequency at the rc-o scillator 2 of 2 mhz c an be obtained by connect- ing a resistor r ext = 360 k ? (see figure 4-15 ). figure 4-15. rc-oscillator 2 4.5.2.4 4-mhz oscillator the ATAR092-C/atar 892-c 4-mhz oscillator options need a crystal or ceramic resonator con- nected to the osc1 and osc2 pins to establish oscillation. all the necessary oscillator circui try is integrated, e xcept the actual crys tal, resonator, c 3 and c 4 . figure 4-16. 4-mhz crystal oscillator note: both, the 4-mhz and the 32-khz crystal oscillator , use an integrated 14 stage divider circuit to sta- bilize oscillation before the oscillator output is used as system clock. this results in an additional delay of about 4 ms for the 4-mhz crystal and about 500 ms for the 32-khz crystal. table 4-5. supervisor function control bits os1 os0 ccs supervisor reset output (res) 110 enable 1 1 1 disable x 0 x disable rc-oscillator 2 rcout2 stop rcout2 osc-stop r trim osc1 osc2 r ext v dd 4-mhz oscillator 4out 4out osc1 osc2 * oscin c 1 * c 2 oscout xtal 4 mhz * mask option stop osc-stop
18 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 4-17. ceramic resonator note: both, the 4-mhz and the 32-khz crystal oscillator , use an integrated 14 stage divider circuit to sta- bilize oscillation before the oscillator output is used as system clock. this results in an additional delay of about 4 ms for the 4-mhz crystal and about 500 ms for the 32-khz crystal. 4.5.2.5 32-khz oscillator some applications require long-term time keeping or low resolution timing. in this case, an on-chip, low power 32-khz crystal oscillator ca n be used to generate both the subcl and the syscl. in this mode, power cons umption is greatly reduced. th e 32-khz crystal oscillator can- not be stopped while the power-down mode is in operation. figure 4-18. 32-khz crystal oscillator note: both, the 4-mhz and the 32-khz crystal oscillator , use an integrated 14 stage divider circuit to sta- bilize oscillation before the oscillator output is used as system clock. this results in an additional delay of about 4 ms for the 4-mhz crystal and about 500 ms for the 32-khz crystal. 4-mhz oscillator 4out stop 4out osc-stop osc1 osc2 * oscin c 1 * c 2 oscout cer. res * mask option c 3 c 4 32-khz oscillator 32out 32out osc1 osc2 * oscin c 1 * c 2 oscout xtal 32 khz * mask option
19 4593d?4bmcu?05/06 ATAR092-C/atar892-c 4.5.3 clock management the clock management register controls the sy stem clock divider and synchronization stage. writing to this register trig gers the synchronization cycle. 4.5.3.1 clock management register (cm) 4.5.3.2 system configuration register (sc) auxiliary register address: ?3?hex bit 3 bit 2 bit 1 bit 0 cm nstop ccs css1 css0 reset value: 1111b nstop n ot stop peripheral clock nstop = 0, stops the peripheral cloc k while the core is in sleep mode nstop = 1, enables the peripheral cl ock while the core is in sleep mode ccs c ore c lock s elect ccs = 1, the internal rc-o scillator 1 generates syscl ccs = 0, the 4-mhz crystal oscillator, the 32-khz crystal oscillator, an external clock source or the rc-oscillator 2 wit h the external resistor at osc1 generates syscl dependent on the setting of os0 and os1 in the system configuration register css1 c ore s peed s elect 1 css0 c ore s peed s elect 0 table 4-6. core speed select css1 css0 divider note 0016 118reset value 104 012 primary register address: ?3?hex bit 3bit 2bit 1bit 0 sc: write bot ? os1 os0 reset value: 1x11b bot b rown- o ut t hreshold bot = 1, low brown-out voltage threshold (1.7 v) bot = 0, high brown-out voltage threshold (2.0 v) os1 o scillator s elect 1 os0 o scillator s elect 0
20 4593d?4bmcu?05/06 ATAR092-C/atar892-c note: if the bit ccs = 0 in the cm-register the rc-oscillator 1 always stops. 4.6 power-down modes the sleep mode is a shut-down condition which is used to reduce the average system power consumption in applications wher e the microcontroller is not fully utilized. in this mode, the sys- tem clock is stopped . the sleep mode is entered via the sl eep instruction. this instruction sets the interrupt enable bit (i) in the condition code register to enable all interrupts and stops the core. during the sleep mode the peripheral modules remain active and are able to generate interrupts. the microcontroller exits the sleep mode by carrying out any interrupt or a reset. the sleep mode can only be maintained when none of the interrupt pending or active register bits are set. the application of the $autosleep routine ensures the correct function of the sleep mode. for standard applications use the $a utosleep routine to enter the power-down mode. using the sleep instruction instead of the $autosleep following an i/o instruction requires insertion of 3 non i/o instruction cycles (for example nop nop nop) between the in or out command and the sleep command. the total power consumption is directly proportional to the active time of the microcontroller. for a rough estimation of the expected average system current consumption, the following formula should be used: i total (v dd ,f syscl ) = i sleep + (i dd t active /t total ) i dd depends on v dd and f syscl the ATAR092-C/atar892-c has various power-down modes. during the sleep mode the clock for the marc4 core is stopped. with the nstop bit in the clock management register (cm) it is programmable if the clock for the on-chip peripherals is active or stopped during the sleep mode. if the clock for the core and the peripherals is stopped the selected oscillator is switched off. an exception is the 32-khz osc illator, if it is selected it runs continuously indepen dent of the nstop bit. if the oscillator is stoppe d or the 32-khz oscillator is selected, power consumption is extremely low. table 4-7. oscillator select mode os1 os0 input for su bcl selected oscillators 111 c in /16 rc-oscillator 1 and external input clock 201 c in /16 rc-oscillator 1 and rc-oscillator 2 310 c in /16 rc-oscillator 1 and 4-mhz crystal oscillator 4 0 0 32 khz rc-oscillator 1 and 32-khz crystal oscillator table 4-8. power-down modes mode cpu core osc-stop (1) brown-out function rc-oscillator 1 rc-oscillator 2 4-mhz oscillator 32-khz oscillator external input clock active run no active run run yes power-down sleep no active run run yes sleep sleep yes stop stop run stop note: 1. osc-stop = sleep and nstop and wdl
21 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5. peripheral modules 5.1 addressing peripherals accessing the peripheral modules takes place via the i/o bus (see figure 5-1 ). the in or out instructions allow direct addressing of up to 16 i/o modules. a dual register addressing scheme has been adopted to enable direct addressing of the primary register. to address the auxiliary register, the access must be switched with an auxiliary switching module. thus a single in (or out) to the module address will read (or write into) the module primary register. accessing the auxiliary register is performed with the same instruction preceded by writing the module address into the auxiliary switching module. byte wide registers are accessed by multiple in (or out) instructions. for more complex peripheral modules, with a larger number of registers, extended addressing is used. in this case, a bank of up to 16 subport registers are indirectly addressed with the subport address. the first out instruction writes the subport address to the sub address register, the second in or out instruction reads data from or writes data to the addressed subport. figure 5-1. example of i/o addressing subaddress reg. subport fh i/o bus aux. reg. bank of primary regs. primary reg. (address pointer) auxiliary switch module indirect subport access to other modules 1 2 (subport register write) 3 4 5 1 2 3 6 6 4 5 example of qforth program code 1 2 4 5 3 6 addr. (asw) = auxililiary switch module address 1 2 2 1 2 2 4 5 5 (auxiliary register write) module asw module m1 module m2 module m3 subport eh primary reg. primary reg. subport 1 subport 0 dual register access single register access addr. (sport) addr. (m1) out sport_data addr. (m1) out (subport register read) addr. (sport) addr. (m1) out addr. (m1) in (subport register write byte) addr. (sport) addr. (m1) out sport_data (lo) addr. (m1) out sport_data (hi) addr. (m1) out (subport register read byte) addr. (sport) addr. (m1) out addr. (m1) in (hi) addr. (m1) in (lo) (primary register write) prim._data addr. (m2) out addr. (m2) addr. (asw) out aux._data addr. (m2) out (primary register read) addr. (m2) in (auxiliary register read ) addr. (m2) addr. (asw) out addr. (m2) in (auxiliary register write byte) addr. (m2) addr. (asw) out aux._data (lo) addr. (m2) out aux._data (hi) addr. (m2) out (primary register write) prim._data addr. (m3) out (primary register read) addr. (m3) in addr. (mx) = module mx address addr. (sport) = subport address prim._data = data to be written into primary register aux._data = data to be written into auxiliary register aux._data (lo) = data to be written into auxiliary register (low nibble) aux._data (hi) = data to be written into auxiliary register (high nibble) sport_data (lo) = data to be written into subport (low nibble) sport_data (hi) = data to be written into subport (high nibble) (lo) = sport_data (low nibble) (hi) = sport_data (high nibble)
22 4593d?4bmcu?05/06 ATAR092-C/atar892-c table 5-1. peripheral addresses port address name write/read reset value register function module type see page 1 p1dat w/r 1xx1b port 1 - data register/input data m3 23 2 p2dat w/r 1111b port 2 - data register/pin data m2 25 auxiliary p2cr w 1111b port 2 - control register 25 3 sc w 1x11b system configuration register m3 19 cwd r xxxxb watchdog reset m3 12 auxiliary cm w 1111b clock management register m2 19 4 p4dat w/r 1111b port 4 - data register/pin data m2 29 auxiliary p4cr w 1111 1111b port 4 - control register (byte) 29 5 p5dat w/r 1111b port 5 - data register/pin data m2 27 auxiliary p5cr w 1111 1111b port 5 - control register (byte) 27 6 p6dat w/r 1xx1b port 6 - data register/pin data m2 30 auxiliary p6cr w 1111b port 6 - control register (byte) 30 7 t12sub w ? data to timer 1/2 subport m1 21 subport address 0 t2c w 0000b timer 2 control register m1 43 1 t2m1 w 1111b timer 2 mode register 1 m1 43 2 t2m2 w 1111b timer 2 mode register 2 m1 45 3 t2cm w 0000b timer 2 compare mode register m1 46 4 t2co1 w 1111b timer 2 compare register 1 m1 47 5 t2co2 w 1111 1111b timer 2 compare register 2 (byte) m1 47 6? ? ?reserved 7? ? ?reserved 8 t1c1 w 1111b timer 1 control register 1 m1 33 9 t1c2 w x111b timer 1 control register 2 m1 34 a wdc w 1111b watchdog control register m1 34 b-f reserved 8 asw w 1111b auxiliary/switch register asw 21 9 stb w xxxx xxxxb serial transmit buffer (byte) m2 72 srb r xxxx xxxxb serial receive buffer (byte) 73 auxiliary sic1 w 1111b serial interface control register 1 70 a sisc w/r 1x11b serial interface status/control register m2 72 auxiliary sic2 w 1111b serial interface control register 2 71 b t3sub w/r ? data to/from timer 3 subport m1 21 subport address 0 t3m w 1111b timer 3 mode register m1 57 1 t3cs w 1111b timer 3 clock select register m1 59 2 t3cm1 w 0000b timer 3 compare mode register 1 m1 60 3 t3cm2 w 0000b timer 3 compare mode register 2 m1 60 4 t3co1 w 1111 1111b timer 3 compare register 1 (byte) m1 61 4 t3cp r xxxx xxxxb timer 3 capture register (byte) m1 61 5 t3co2 w 1111 1111b timer 3 compare register 2 (byte) m1 61 6-f ? reserved c t3c w 0000b timer 3 control register m3 58 t3st r x000b timer 3 status register m3 58 d ? ? reserved e ? ? reserved f vmc w 1111b voltage monitor control register m3 13 vmst r xx11b voltage monitor status register m3 13
23 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.2 bi-directional ports with the exception of port 1 and port 6, all other ports (2, 4 and 5) are 4 bits wide. port 1 and port 6 have a data width of 2 bits (bit 0 and bit 3). all ports may be used for data input or output. all ports are equipped with schmitt trigger inputs and a variety of mask options for open drain, open source, full complementary outputs, pull-up and pull-down transistors. all port data regis- ters (pxdat) are i/o mapped to the primary address register of the respective port address and the port control register (pxcr), to the corresponding auxiliary register. there are five different directional ports available: port 1 2-bit wide bi-directiona l ports with automatic full bus width direction switching port 2 4-bit wide bitwise-programmable i/o port port 5 4-bit wide bitwise-programmable bi-directional port with optional strong pull-ups and programmable interrupt logic port 4 4-bit wide bitwise-programmable bi-d irectional port also provides the i/o interface to timer 2, ssi, voltage monitor input and external interrupt input port 6 2-bit wide bitwise-programmable bi-d irectional port also provides the i/o interface to timer 3 and the external interrupt input 5.2.1 bi-directional port 1 in port 1 the data direction register is not independently software programmable, the direction of the complete port being switched automatically when an i/o instruction occurs (see figure 5-2 on page 24 ). the port is switched to output mode via an out instruction and to input via an in instruction. the data written to a port will be stored into the output data latches and appears immediately at the port pin follo wing the out instruction. after r eset all output latches are set to 1 and the port is switched to input mode. an in instruction reads the condition of the associ- ated pins. note: care must be taken when switching the bi-directional port from output to input. the capacitive pin loading at this port in conjunction with the high resistance pull-ups may cause the cpu to read the contents of the output data regist er rather than the external input state. to avoid this, one of the following programming techniques should be used: use two in-instructions and drop the first data ni bble. the first in switches the port from output to input and the drop removes the first invalid nibble. the second in reads the valid pin state. use an out-instruction followed by an in-instructi on. via the out-instruction, the capacitive load is charged or discharged depending on the optional pull-up/pull-down configuration. write a 1 for pins with pull-up resistors and a 0 for pins with pull-down resistors.
24 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-2. bi-directional port 1 5.2.2 bi-directional port 2 as all other bi-directional ports, this port includes a bitwise programmable control register (p2cr), which enables the individual programming of each port bit as input or output. it also opens up the possibility of reading the pin condition when in output mode. this is a useful fea- ture for self testing and for serial bus applications. port 2, however, has an in creased drive capability and an additional low resistance pull-up/-down transistor mask option. care should be taken connecting external components to bp20/nte. during any reset phase, the bp20/nte input is driven towards v dd by an additional internal strong pull-up transistor. this pin must not be pulled down (active or passive) to v ss during reset by any external circuitry rep- resenting a resistor of less than 150 k ? . this prevents the circuit from unintended switching to test mode enable through the application circuitry at pin bp20/nte. resistors less than 150 k ? might lead to an undefined state of the internal test logic thus disabling the application firmware. to avoid any conflict with the optional internal pull-down transistors, bp20 handles the pull-down options in a different way than all other ports. bp20 is the only port that switches off the pull-down transistors during reset. out in reset i/o bus d r s q q nq r master reset p1daty (data out) (direction) bp1y v dd swi t ched pull-up (1) (1) mask opti ons st at i c pul l -up st at i c pull-dow n swi tched pul l -down v dd (1) (1) (1)
25 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-3. bi-directional port 2 5.2.2.1 port 2 data register (p2dat) bit 3 = msb, bit 0 = lsb 5.2.2.2 port 2 control register (p2cr) value 1111b means all pins in input mode master reset q q bp2y (1) mask options p2daty p2cry i/o bus d i/o bus i/o bus switched pull-up static pull-up (data out) (direction) s d (1) s static pull-down switched pull-down v dd v dd (1) (1) (1) (1) (1) primary register address: '2'hex bit 3bit 2bit 1bit 0 p2dat p2dat3 p2dat2 p2dat1 p2dat0 reset value: 1111b auxiliary register address: '2'hex bit 3 bit 2 bit 1 bit 0 p2cr p2cr3 p2cr2 p2cr1 p2cr0 reset value: 1111b table 5-2. port 2 control register code 3 2 1 0 function x x x 1 bp20 in input mode x x x 0 bp20 in output mode x x 1 x bp21 in input mode x x 0 x bp21 in output mode x 1 x x bp22 in input mode x 0 x x bp22 in output mode 1 x x x bp23 in input mode 0 x x x bp23 in output mode
26 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.2.3 bi-directional port 5 as all other bi-directional ports, this port includes a bitwise programmable control register (p5cr), which allows the individual programming of each port bit as input or output. it also opens up the possibility of reading the pin condition when in output mode. this is a useful fea- ture for self-testing and for serial bus applications. the port pins can also be used as external interrupt inputs (see figure 5-4 and figure 5-5 on page 27 ). the interrupts (int1 and int6) can be masked or independently configured to trigger on either edge. the interrupt configuration and port direction is controlled by the port 5 control register (p5cr). an additional low resistance pull-up/-down transistor mask option provides an internal bus pull-up for serial bus applications. the port 5 data register (p5dat) is i/o mapped to the primary address register of address ?5?h and the port 5 control register (p5cr) to the corresponding aux iliary register. the p5cr is a byte-wide register and is configured by writi ng first the low nibble and then the high nibble (see section ?addressing peripherals?). figure 5-4. bi-directional port 5 master reset q v dd bp5y (1) mask options p5daty i/o bus d in enable i/o bus (1) switched pull-up switched pull-down static pull-up (data out) s static pull-down v dd v dd (1) (1) (1) (1) (1)
27 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-5. port 5 external interrupts 5.2.3.1 port 5 data register (p5dat) 5.2.3.2 port 5 control register (p5cr) byte write p5xm2, p5xm1 ? port 5x interrupt mode/direction code bidir. port data in in_enable bp53 p53m2 p53m1 p52m2 p52m1 p51m2 p51m1 p50m2 p50m1 decoder decoder decoder decoder bidir. port data in in_enable bp52 i/o-bus bidir. port data in in_enable bp51 i/o-bus bidir. port data in in_enable bp50 int1 int6 p5cr primary register address: '5'hex bit 3bit 2bit 1bit 0 p5dat p5dat3 p5dat2 p5dat1 p5dat0 reset value: 1111b auxiliary register address: '5'hex bit 3bit 2bit 1bit 0 p5cr first write cycle p51m2 p51m1 p50m2 p50m1 reset value: 1111b bit 7bit 6bit 5bit 4 second write cycle p53m2 p53m1 p52m2 p52m1 reset value: 1111b
28 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.2.4 bi-directional port 4 the bi-directional port 4 is a bitwise configurab le i/o port and provides the external pins for timer 2, ssi and the voltage monitor input (vmi). as a normal port, it performs in exactly the same way as bi-directional port 2 (see figure 5-3 on page 25 ). two additional multiplexes allow data and port direction control to be passed over to other internal modules (timer 2, vm or ssi). the i/o pins for sc and sd lines have an additional mode to generate an ssi-interrupt. all four port 4 pins can be individ ually switched by the p4cr register. figure 5-6 shows the inter- nal interfaces to bi-directional port 4. figure 5-6. bi-directional port 4 and port 6 table 5-3. port 5 control register auxiliary address: '5'hex first write cycle second write cycle code 3 2 1 0 function code 3 2 1 0 function x x 1 1 bp50 in input mode ? interrupt disabled x x 1 1 bp52 in input mode ? interrupt disabled x x 0 1 bp50 in input mode ? rising edge interrupt x x 0 1 bp52 in input mode ? rising edge interrupt x x 1 0 bp50 in input mode ? falling edge interrupt x x 1 0 bp52 in input mode ? falling edge interrupt x x 0 0 bp50 in output mode ? interrupt disabled x x 0 0 bp52 in output mode ? interrupt disabled 1 1 x x bp51 in input mode ? interrupt disabled 1 1 x x bp53 in input mode ? interrupt disabled 0 1 x x bp51 in input mode ? rising edge interrupt 0 1 x x bp53 in input mode ? rising edge interrupt 1 0 x x bp51 in input mode ? falling edge interrupt 1 0 x x bp53 in input mode ? falling edge interrupt 0 0 x x bp51 in output mode ? interrupt disabled 0 0 x x bp53 in output mode ? interrupt disabled master reset q v dd bpxy (1) mask options pxdaty i/o bus d i/o bus i/o bus switched pull-up switched pull-down s pxcry s q d pxmry pout (direction) pdir intx (1) pin static pull-up static pull-down v dd v dd (1) (1) (1) (1) (1)
29 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.2.4.1 port 4 data register (p4dat) 5.2.4.2 port 4 control register (p4cr) byte write p4xm2, p4xm1 - port 4x interrupt mode/direction code primary register address: '4'hex bit 3 bit 2 bit 1 bit 0 p4dat p4dat3 p4dat2 p4dat1 p4dat0 reset value: 1111b auxiliary register address: '4'hex bit 3 bit 2 bit 1 bit 0 p4cr first write cycle p41m2 p41m1 p40m2 p40m1 reset value: 1111b bit 7 bit 6 bit 5 bit 4 second write cycle p43m2 p43m1 p42m2 p42m1 reset value: 1111b table 5-4. port 4 control register auxiliary address: '4'hex first write cycle second write cycle code 3 2 1 0 function code 3 2 1 0 function x x 1 1 bp40 in input mode x x 1 1 bp42 in input mode x x 1 0 bp40 in output mode x x 1 0 bp42 in output mode x x 0 1 bp40 enable alternate function (sc for ssi) x x 0 x bp42 enable alternate function (t2o for timer 2) x x 0 0 bp40 enable alternate function (falling edge interrupt input for int3) 1 1 x x bp43 in input mode 1 1 x x bp41 in input mode 1 0 x x bp43 in output mode 1 0 x x bp41 in output mode 0 1 x x bp43 enable alternate function (sd for ssi) 0 1 x x bp41 enable alternate function (vmi for voltage monitor input) 0 0 x x bp43 enable alternate function (falling edge interrupt input for int3) 0 0 x x bp41 enable alternate function (t2i external clock input for timer 2) ??
30 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.2.5 bi-directional port 6 the bi-directional port 6 is a bitwise configurab le i/o port and provides the external pins for timer 3. as a normal port, it performs in exactl y the same way as bi-directional port 6 (see fig- ure 5-6 on page 28 ). two additional multiplexes allow data and port direction control to be passed over to other internal modules (timer 3). the i/o pin for t3i line has an additional mode to generate a timer 3 interrupt. all two port 6 pins can be individua lly switched by the p6cr register. figure 5-6 on page 28 shows the internal interfaces to bi-directional port 6. 5.2.5.1 port 6 data register (p6dat) 5.2.5.2 port 6 control register (p6cr) p6xm2, p6xm1 - port 6x interrupt mode/direction code primary register address: '6'hex bit 3 bit 2 bit 1 bit 0 p6dat p6dat3 ? ? p6dat0 reset value: 1xx1b primary register address: '6'hex bit 3 bit 2 bit 1 bit 0 p6cr p63m2 p63m1 p60m2 p60m0 reset value: 1111b table 5-5. port 6 control register auxiliary address: ?6?hex write cycle code 3 2 1 0 function code 3 2 1 0 function x x 1 1 bp60 in input mode 1 1 x x bp63 in input mode x x 1 0 bp60 in output mode 1 0 x x bp63 in output mode x x 0 x bp60 enable alternate port function (t3o for timer 3) 0 x x x bp63 enable alternate port function (t3i for timer 3)
31 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3 universal timer/counter/ communication module (utcm) the universal timer/counter/communication module (utcm) consists of three timers (timer 1,timer 2, timer 3) and a sync hronous serial interface (ssi). timer 1 is an interval timer that can be used to generate periodic interrupts and as prescaler for timer 2, timer 3, the serial interface and the watchdog function. timer 2 is an 8/12-bit timer with an external clock input (t2i) and an output (t2o). timer 3 is an 8-bit timer/counter with its own input (t3i) and output (t3o). the ssi operates as a two-wire serial interface or as a shift register for modulation and demodulation. the modulator and demodulator units work together with the timers and shift the data bits into or out of the shift register. there is a multitude of modes in which the timers and the serial interface can work together. figure 5-7. utcm block diagram demodu- lator 3 8-bit counter 3 capture 3 compare 3/1 compare 3/2 modu- lator 3 mux mux control watchdog interval/prescaler timer 1 timer 3 modu- lator 2 4-bit counter 2/1 compare 2/1 mux mux dcg 8-bit counter 2/2 compare 2/2 control timer 2 mux 8-bit shift register receive buffer transmit buffer control ssi scl int4 int5 int2 nrst int3 pout tog2 tog3 t1out subcl syscl from clock module t3o t3i t2i t2o sc sd i/o bus
32 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.1 timer 1 timer 1 is an interval timer which can be used to generate periodic interrupts and as a prescaler for timer 2, timer 3, the serial interface and the watchdog function. timer 1 consists of a programma ble 14-stage divider that is dr iven by either subcl or syscl. the timer output signal can be used as a prescale r clock or as a subcl and as a source for the timer 1 interrupt. because of other system requirements the timer 1 output t1out is synchro- nized with syscl. therefore, in the power-down mode sl eep (cpu core -> sleep and osc-stop -> yes), the output t1out is stopped (t1out = 0). nevertheless, timer 1 can be active in sleep and generate time r 1 interrupts. the in terrupt is maskable via the t1im bit and the subcl can be bypassed via the t1bp bit of the t1c2 register. the time interval for the timer output can be programmed via timer 1 control register t1c1. this timer starts running automatically after any power-on reset. if the watchdog function is not activated, the timer can be restarted by writing into the t1c1 register with t1rm = 1. timer 1 can also be used as a watchdog timer to prevent a system from stalling. the watchdog timer is a 3-bit counter that is supplied by a separate output of timer 1. it generates a system reset when the 3-bit counter overflows. to avoid this, the 3-bit counter must be reset before it overflows. the application software has to accomplish this by reading the cwd register. after power-on reset the watchdog must be activa ted by software in the $reset initialization routine. there are two watchdog modes, in one mode the watchdog can be switched on and off by software, in the other mode the watchdog is active and locked. this mode can only be stopped by carrying out a system reset. the watchdog timer operation mode and the time interval for the watchdog reset can be pro- grammed via the watchdog control register (wdc). figure 5-8. timer 1 module 14-bit prescaler cl1 4-bit watchdog mux wdcl t1im t1bp t1mux nrst int2 t1out t1cs syscl subcl
33 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-9. timer 1 and watchdog 5.3.1.1 timer 1 control register 1 (t1c1) bit 3 = msb, bit 0 = lsb the three bits t1c[2:0] select the divider for timer 1. the resulting time interval depends on this divider and the timer 1 input clock source. the timer input can be supplied by the system clock, the 32 khz oscillator or via cl ock management. if clock managem ent generates the subcl, the selected input clock from the rc o scillator, 4 mhz oscillato r or an external clock is divided by 16. q5 q1 q2 q3 q4 q6 q8 q8 q11 q11 q14 q14 res cl decoder watchdog mode control mux for interval timer decoder mux for watchdog timer t1rm t1c2 t1c1 t1c0 3 2 wdl wdr wdt1 wdt0 wdc res t1mux subcl t1bp t1im t1im=0 t1im=1 int2 t1out t1c2 reset (nrst) watchdog divider / 8 divider reset t1c1 write of the t1c1 register cl1 wdcl read of the cwd register address: '7'hex - subaddress: '8'hex bit 3 bit 2 bit 1 bit 0 t1c1 t1rm t1c2 t1c1 t1c0 reset value: 1111b t1rm t imer 1 r estart m ode t1rm = 0, write access without timer 1 restart t1rm = 1, write access with timer 1 restart note: if wdl = 0, timer 1 restart is impossible t1c2 t imer 1 c ontrol bit 2 t1c1 t imer 1 c ontrol bit 1 t1c0 t imer 1 c ontrol bit 0
34 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.1.2 timer 1 control register 2 (t1c2) bit 3 = msb, bit 0 = lsb 5.3.1.3 watchdog control register (wdc) bit 3 = msb, bit 0 = lsb table 5-6. timer 1 control bits t1c2 t1c1 t1c0 divider time interval with subcl time interval with subcl = 32 khz time interval with syscl = 2/1 mhz 0 0 0 2 subcl/2 61 s 1 s/2 s 0 0 1 4 subcl/4 122 s 2 s/4 s 0 1 0 8 subcl/8 244 s 4 s/8 s 0 1 1 16 subcl/16 488 s 8 s/16 s 1 0 0 32 subcl/32 0.977 ms 16 s/32 s 1 0 1 256 subcl/256 7.812 ms 128 s/256 s 1 1 0 2048 subcl/2048 62.5 ms 1024 s/2048 s 1 1 1 16384 subcl/16384 500 ms 8192 s/16384 s address: ?7?hex - subaddress: ?9?hex bit 3 bit 2 bit 1 bit 0 t1c2 ? t1bp t1cs t1im reset value: x111b t1bp t imer 1 subcl b y p assed t1bp = 1, t1out = t1mux t1bp = 0, t1out = subcl t1cs t imer 1 input c lock s elect t1cs = 1, cl1 = subcl (see figure 5-8 on page 32 ) t1cs = 0, cl1 = syscl (see figure 5-8 on page 32 ) t1im t imer 1 i nterrupt m ask t1im = 1, disables timer 1 interrupt t1im = 0, enables timer 1 interrupt address: ?7?hex - subaddress: ?a?hex bit 3 bit 2 bit 1 bit 0 wdc wdl wdr wdt1 wdt0 reset value: 1111b
35 4593d?4bmcu?05/06 ATAR092-C/atar892-c both these bits control the time interval for the watchdog reset. 5.3.2 timer 2 this is an 8-bit or 12-bit timer used for interrupt, square-wave, pulse and duty cycle generation baud-rate generation for the internal shift register manchester and bi-phase modulation together with the ssi carrier frequency generation and modulation together with the ssi timer 2 can be used as an interval timer for interrupt generation, as a signal generator or as a baud-rate generator and modulator for the serial interface. it consists of a 4-bit and an 8-bit up counter stage which both have compare registers. the 4-bit counter stages of timer 2 are cas- cadable as a 12-bit timer or as 8-bit timer with a 4-bit prescaler. the timer can also be configured as an 8-bit timer and a separate 4-bit prescaler. timer 2 input can be supplied via t he system clock, the external input clock (t2i), the timer 1 output clock, the timer 3 output clock or the shift clock of the serial interface. the external input clock t2i is not synchronized with syscl. therefore, it is possible to use timer 2 with a higher clock speed than syscl. furthermore, with that input clock timer 2 operates in the power-down mode sleep (cpu core -> sleep and osc-stop -> yes) as well as in power-down (cpu core -> sleep and osc-stop -> no). all other clock sources supply no clock signal in sleep if nstop = 0. the 4-bit counter stages of timer 2 have an additional clock output (pout). its out- put has a modulator stage that allows the generation of pulses as well as the generation and modulation of carrier frequencies. timer 2 output can modulate with the shift register data output to generate bi-phase- or manchester-code. wdl w atch d og l ock mode wdl = 1, the watchdog can be enabled and disabled by using the wdr-bit wdl = 0, the watchdog is enabled and locked. in this mode the wdr-bit has no effect. after the wd l-bit is cleared, th e watchdog is acti ve until a system reset or power-on reset occurs. wdr w atch d og r un and stop mode wdr = 1, the watchdog is stopped/disabled wdr = 0, the watchdog is active/enabled wdt1 w atch d og t ime 1 wdt0 w atch d og t ime 0 table 5-7. watchdog time control bits wdt1 wdt0 divider delay time to reset with subcl = 32 khz delay time to reset with syscl = 2/1 mhz 0 0 512 15.625 ms 0.256 ms/0.512 ms 0 1 2048 62.5 ms 1.024 ms/2.048 ms 1 0 16384 0.5 s 8.2 ms/16.4 ms 1 1 131072 4 s 65.5 ms/131 ms
36 4593d?4bmcu?05/06 ATAR092-C/atar892-c if the serial interface is used to modulate a bit-stream, the 4-bit stage of timer 2 has a special task. the shift register can only handle bit-stream lengths divisible by 8. for other lengths, the 4-bit counter stage can be used to stop the modulator after the right bit-count is shifted out. if the timer is used for carrier frequency modulation, the 4-bit stage works together with an addi- tional 2-bit duty cycle generator like a 6-bit pr escaler to a generate carrier frequency and duty cycle. the 8-bit counter is used to enable and disable the modulator output for a programmable count of pulses. for programming the time interval, the timer has a 4-bit and an 8-bit compare register. for pro- gramming the timer function, it has four modes and control registers. the comparator output of stage 2 is controlled by a special compare mode register (t2cm). this register contains mask bits for the actions (counter reset, output toggle, timer interrupt) which can be triggered by a compare match event or the counter overflow. this architecture enables the timer to function in various modes. timer 2 has a 4-bit compare register (t2co1) and an 8-bit compare register (t2co2). both these compare registers are cascadable as a 12-bit compare register, or 8-bit compare register and 4-bit compare register. figure 5-10. timer 2 for 12-bit compare data value: m = x + 1 0 x 4095 for 8-bit compare data value: n = y + 1 0 y 255 for 4-bit compare data value: l = z + 1 0 z 15 4-bit counter 2/1 res ovf1 compare 2/1 t2co1 cm1 pout ssi pout cl2/2 dcg t2m1 p4cr 8-bit counter 2/2 res ovf2 compare 2/2 t2co2 t2cm control tog2 int4 bi-phase manchester modulator output mout m2 to modulator 3 t2o timer 2 modulator output-stage t2m2 so control ssi ssi i/o-bus t2c cl2/1 t2i syscl t1out tog3 scl i/o-bus dcgo
37 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.2.1 timer 2 modes mode 1: 12-bit compare counter the 4-bit stage and the 8-bit stage work together as a 12-bit compare counter. a compare match signal of the 4-bit and the 8-bit stage generates the signal for the counter reset, toggle flip-flop or interrupt. the compare action is programmable via the compare mode register (t2cm). the 4-bit counter overflow (ovf1) supplies the clock output (pout) with clocks. the duty cycle gen- erator (dcg) has to be bypassed in this mode. figure 5-11. 12-bit compare counter mode 2: 8-bit compare counter with 4-bit programmable prescaler the 4-bit stage is used as a programmable prescaler for the 8-bit counter stage. in this mode, a duty cycle stage is also available. this stage can be used as an additional 2-bit prescaler or for generating duty cycles of 25%, 33% and 50%. the 4- bit compare output (cm1) supplies the clock output (pout) with clocks. figure 5-12. 8-bit compare counter 4-bit counter 4-bit compare res 4-bit register cm1 pout (cl2/1 /16) 8-bit counter 8-bit compare 8-bit register ovf2 cm2 res t2rm t2otm timer 2 output mode and t2otm-bit t2im t2ctm tog2 int4 cl2/1 dcg t2d1, 0 4-bit counter 4-bit compare res 4-bit register cm1 pout 8-bit counter 8-bit compare 8-bit register ovf2 cm2 res t2rm t2otm timer 2 output mode and t2otm-bit t2im t2ctm tog2 int4 cl2/1 dcg t2d1, 0 dcgo
38 4593d?4bmcu?05/06 ATAR092-C/atar892-c mode 3/4: 8-bit compare counter and 4-bit programmable prescaler in these modes the 4-bit and the 8-bit counter stages work independently as a 4-bit prescaler and an 8-bit timer with an 2-bit prescaler or as a duty cycle generator. only in mode 3 and mode 4, can the 8-bit counter be supplied via the exte rnal clock input (t2i) which is selected via the p4cr register. the 4-bit prescaler is started by activating mode 3 and stopped and reset in mode 4. changing mode 3 and 4 has no effect for the 8-bit timer stage. the 4-bit stage can be used as a prescaler for timer 3, the ssi or to generate the stop signal for modulator 2 and modulator 3. figure 5-13. 4-/8-bit compare counter 5.3.2.2 timer 2 output modes the signal at the timer output is generated via modulator 2. in the toggle mode, the compare match event toggles the output t2o. for high re solution duty cycle modulation 8 bits or 12 bits can be used to toggle the output. in the duty cycle burst modulator modes the dcg output is connected to t2o and switched on and off either by the toggle flip flop output or the serial data line of the ssi. modulator 2 also has 2 modes to output the content of the serial interface as bi-phase- or manchester-code. the modulator output stage can be configured by the output control bits in the t2m2 register. the modulator is started with the start of the shift register (sir = 0) and stopped either by carry- ing out a shift register stop (sir = 1) or compare match event of stage 1 (cm1) of timer 2. for this task, timer 2 mode 3 must be used and the prescaler has to be supplied with the internal shift clock (scl). 4-bit counter 4-bit compare res 4-bit register 8-bit counter 8-bit compare 8-bit register ovf2 cm2 res t2rm t2otm timer 2 output mode and t2otm-bit t2im t2ctm tog2 int4 cl2/2 dcg t2d1, 0 dcgo p41m2, 1 p4cr cm1 pout cl2/1 mux tog3 t1out syscl scl t2cs1, 0 syscl t2i
39 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-14. timer 2 modulator output stage 5.3.2.3 timer 2 output signals timer 2 output mode 1 toggle mode a: a timer 2 compare match toggles the output flip-flop (m2) -> t2o figure 5-15. interrupt timer/square wave generator ? the output toggles with each edge compare match event toggle res/set bi-phase/ manchester modulator t2top t2os2, 1, 0 t2m2 t2o m2 m2 s1 s2 s3 modulator 3 re fe omsk ssi control tog2 so dcgo 4 000123 4 0123 4 0123 01 input counter 2 t2r counter 2 cmx int4 t2o
40 4593d?4bmcu?05/06 ATAR092-C/atar892-c toggle mode b: a timer 2 compare match toggles the output flip-flop (m2) -> t2o figure 5-16. pulse generator ? the timer output toggles with the timer start if the t2ts-bit is set toggle mode c : a timer 2 compare match toggles the output flip-flop (m2) -> t2o figure 5-17. pulse generator ? the timer toggles with timer overflow and compare match 4 000123 567 4 0123 56 input counter 2 t2r counter 2 cmx int4 t2o toggle by start t2o 4095/ 255 4 000123 567 4 0123 56 input counter 2 t2r counter 2 cmx ovf2 int4 t2o 4095/ 255
41 4593d?4bmcu?05/06 ATAR092-C/atar892-c timer 2 output mode 2 duty cycle burst generator 1: the dcg output signal (dcgo) is given to the output, and gated by the output flip-flop (m2) figure 5-18. carrier frequency burst modulation with timer 2 toggle flip-flop output timer 2 output mode 3 duty cycle burst generator 2: the dcg output signal (dcgo) is given to the output, and gated by the ssi internal data output (so) figure 5-19. carrier frequency burst modulation with the ssi data output timer 2 output mode 4 bi-phase modulator: timer 2 modulates the ssi internal data output (so) to bi-phase code. figure 5-20. bi-phase modulation 1 20120123450120123456780123456789 10 012345 dcgo counter 2 tog2 m2 t2o counter = compare register (= 2) 1 201201201201201201201201201201201201201 dcgo counter 2 tog2 so t2o counter = compare register (= 2) bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 bit 8 bit 9 bit 10 bit 11 bit 12 bit 13 tog2 sc so t2o 000 0 0011 0101 11 1 1 8-bit sr data bit 7 bit 0 data: 00110101
42 4593d?4bmcu?05/06 ATAR092-C/atar892-c timer 2 output mode 5 manchester modulator: timer 2 modulates the ssi internal data output (so) to manchester-code figure 5-21. manchester modulation timer 2 output mode 7 in this mode the timer overflow defines the period and the compare register defines the duty cycle. during one period only the first compare ma tch occurrence is used to toggle the timer out- put flip-flop, until the overflow all further com pare match are ignored. this avoids the situation where changing the compare register causes the occurrence of several compare matches dur- ing one period. the resolution at the pulse-width modulation timer 2 mode 1 is 12-bit and all other timer 2 modes are 8-bit. pwm mode: pulse-width modulation output on timer 2 output pin (t2o) figure 5-22. pwm modulation tog2 sc so t2o 00 0 0011 0101 11 1 1 8-bit sr data bit 7 bit 0 0 bit 7 bit 0 data: 00110101 0 0 50 255 100 0 255 0 150 255 0 50 255 0 100 t2r input clock counter 2/2 counter 2/2 ovf2 cm2 int4 t2o load the next compare value t2co2 = 150 load load t1 t2 t3 t1 t2 tt t t t
43 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.2.4 timer 2 registers timer 2 has 6 control registers to configure the timer mode, the time interval, the input clock and its output function. all registers are indire ctly addressed using extended addressing as described in the section ?addressi ng peripherals?. the alternate functions of the ports bp41 or bp42 must be selected with the port 4 control register p4cr if one of the timer 2 modes require an input at t2i/bp41 or an output at t2o/bp42. 5.3.2.5 timer 2 control register (t2c) 5.3.2.6 timer 2 mode register 1 (t2m1) address: '7'hex - subaddress: '0'hex bit 3bit 2bit 1bit 0 t2c t2cs1 t2cs0 t2ts t2r reset value: 0000b t2cs1 t imer 2 c lock s elect bit 1 t2cs0 t imer 2 c lock s elect bit 0 table 5-8. timer 2 clock select bits t2cs1 t2cs0 input clock (cl 2/1) of counter stage 2/1 0 0 system clock (syscl) 0 1 output signal of timer 1 (t1out) 1 0 internal shift clock of ssi (scl) 1 1 output signal of timer 3 (tog3) t2ts t imer 2 t oggle with s tart t2ts = 0, the output flip-flop of time r 2 is not toggled with the timer start t2ts = 1, the output flip-flop of timer 2 is toggled when the timer is started with t2r t2r t imer 2 r un t2r = 0, timer 2 stop and reset t2r = 1, timer 2 run address: '7'hex - subaddress: '1'hex bit 3 bit 2 bit 1 bit 0 t2m1 t2d1 t2d0 t2ms1 t2ms0 reset value: 1111b t2d1 t imer 2 d uty cycle bit 1 t2d0 t imer 2 d uty cycle bit 0
44 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.2.7 duty cycle generator the duty cycle generator generates duty cycles of 25%, 33% or 50%. the frequency at the duty cycle generator output depends on the duty cycle and the ti mer 2 prescaler setting. the dcg-stage can also be used as additional programmable prescaler for timer 2. figure 5-23. dcg output signals table 5-9. timer 2 duty cycle bits t2d1 t2d0 function of duty cycle generator (dcg) additional divider effect 1 1 bypassed (dcgo0) /1 1 0 duty cycle 1/1 (dcgo1) /2 0 1 duty cycle 1/2 (dcgo2) /3 0 0 duty cycle 1/3 (dcg03) /4 t2ms1 t imer 2 m ode s elect bit 1 t2ms0 t imer 2 m ode s elect bit 0 table 5-10. timer 2 mode select bits mode t2ms1 t2ms0 clock output (pout) timer 2 modes 1 1 1 4-bit counter overflow (ovf1) 12-bit compare counter, the dcg have to be bypassed in this mode 2 1 0 4-bit compare output (cm1) 8-bit compare counter with 4-bit programmable prescaler and duty cycle generator 3 0 1 4-bit compare output (cm1) 8-bit compare counter clocked by syscl or the external clock input t2i, 4-bit prescaler run, the counter 2/1 starts after writing mode 3 4 0 0 4-bit compare output (cm1) 8-bit compare counter clocked by syscl or the external clock input t2i, 4-bit prescaler stop and resets dcgin dcgo0 dcgo1 dcgo2 dcgo3
45 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.2.8 timer 2 mode register 2 (t2m2) if one of these output modes is used the t2o alternate function of port 4 must also be activated. address: '7'hex - subaddress: '2'hex bit 3 bit 2 bit 1 bit 0 t2m2 t2top t2os2 t2os1 t2os0 reset value: 1111b t2top t imer 2 t oggle o utput p reset this bit allows the programmer to preset the timer 2 output t2o. t2top = 0, resets the toggle ou tputs with the write cycle (m2 = 0) t2top = 1, sets toggle output s with the write cycle (m2 = 1) note: if t2r = 1, no output preset is possible t2os2 t imer 2 o utput s elect bit 2 t2os1 t imer 2 o utput s elect bit 1 t2os0 t imer 2 o utput s elect bit 0 table 5-11. timer 2 output select bits output mode t2os2 t2ms1 t2ms0 clock output 1111 toggle mode: a timer 2 compare match toggles the output flip-flop (m2) t2o 2110 duty cycle burst generator 1: the dcg output signal (dcg0) is given to the output and gated by the output flip-flop (m2) 3101 duty cycle burst generator 2: the dcg output signal (dcgo) is given to the output and gated by the ssi internal data output (so) 4100 bi-phase modulator: timer 2 modulates the ssi internal data output (so) to bi-phase code 5011 manchester modulator: timer 2 modulates the ssi internal data output (so) to manchester code 6010 ssi output: t2o is used directly as ssi internal data output (so) 7 0 0 1 pwm mode: an 8/12-bit pwm mode 8 0 0 0 not allowed
46 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.2.9 timer 2 compare and compare mode registers timer 2 has two separate compare registers, t2co1 for the 4-bit stage and t2co2 for the 8-bit stage of timer 2. the timer compares the contents of the compare register current counter value, and if it matches, it generates an output signal. dependent on the timer mode, this signal is used to generate a timer interrupt, to toggle the output flip-flop as an ssi clock or as a clock for the next co unter stage. in the 12-bit timer mode, t2co1 contains bits 0 to 3 and t2co2 bits 4 to 11 of the 12-bit com- pare value. in all other modes, the two compare registers work independently as a 4- and 8-bit compare register. when assigned to the co mpare register a compare event will be suppressed. 5.3.2.10 timer 2 compare mode register (t2cm) address: '7'hex - subaddress: '3'hex bit 3 bit 2 bit 1 bit 0 t2cm t2otm t2ctm t2rm t2im reset value: 0000b t2otm t imer 2 o verflow t oggle m ask bit t2otm = 0, disable overflow toggle t2otm = 1, enable overflow toggle, a c ounter overflow (ovf2) toggles the output flip-flop (tog2). if the t2otm-bit is set, only a counter overflow can generate an interrupt except on the timer 2 output mode 7. t2ctm t imer 2 c ompare t oggle m ask bit t2ctm = 0, disable compare toggle t2ctm = 1, enable compare toggle, a match of the counter with the compare register toggles output flip-flop (tog2). in timer 2 output mode 7 and when the t2ctm-bit is set, only a match of the counter with the compare register can generate an interrupt. t2rm t imer 2 r eset m ask bit t2rm = 0, disable counter reset t2rm = 1, enable counter reset, a match of the counter with the compare register resets the counter t2im t imer 2 i nterrupt m ask bit t2im = 0, disable timer 2 interrupt t2im = 1, enable timer 2 interrupt table 5-12. timer 2 toggle mask bits timer 2 output mode t2otm t2ctm timer 2 interrupt source 1, 2, 3, 4, 5 and 6 0 x compare match (cm2) 1, 2, 3, 4, 5 and 6 1 x overflow (ovf2) 7 x 1 compare match (cm2)
47 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.2.11 timer 2 compare register 1 (t2co1) in prescaler mode the clock is bypassed if the compare register t2co1 contains 0. 5.3.2.12 timer 2 compare register 2 (t2co2) byte write 5.3.3 timer 3 the features of timer 3 are: 2 compare registers capture register edge sensitive input with zero cross detection capability trigger and single action modes output control modes automatically modulation and demodulation modes fsk modulation pulse width modulation (pwm) manchester demodulation together with ssi bi-phase demodulation together with ssi pulse-width demodulation together with ssi address: '7'hex -subaddress: '4'hex t2co1 write cycle bit 3 bit 2 bit 1 bit 0 reset value: 1111b address: '7'hex - subaddress: '5'hex t2co2 first write cycle bit 3 bit 2 bit 1 bit 0 reset value: 1111b second write cycle bit 7 bit 6 bit 5 bit 4 reset value: 1111b
48 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-24. timer 3 timer 3 consists of an 8-bit up-counter with two compare registers and one capture register. the timer can be used as an event counter, a timer and a signal generator. its output can be pro- grammed as modulator and demodulator for the serial interface. the two compare registers enable various modes of signal generation, modulation and demodulation. the counter can be driven by internal and external clock sources. fo r external clock sources, it has a programmable edge-sensitive input which can be used as a counter input, a capture signal input or a trigger input. this timer input is synch ronized with syscl. th erefore, in the po wer-down mode sleep (cpu core -> sleep and osc-stop -> yes), this timer input is stopped too. the counter is read- able via its capture register while it is running. in capture mode, the counter value can be captured by a programmable capture event from the timer 3 input or timer 2 output. a special feature of this timer is the trigger- and single-action mode. in trigger mode, the counter starts counting when triggered by the external signal at its input. in single-action mode, the counter counts only one time up to the programmed compare match event. these modes are very useful for modulation, demodulation, si gnal generation, signal measurement and phase control. for phase control, the timer input is protected against negative voltages and has zero-cross detect ion capability. timer 3 has a modulator output stage and input functions for demodulation. as a modulator it works together with timer 2 or the serial interface. when the shift register is used for modulation the data shifted out of the register is encoded bitwise. in all demodulation modes, the decoded data bits are shifted automatically into the shift register. 8-bit counter 3 res compare 3/1 t3co1 t3cp t3co2 control t3o cl3 t3i t3ex syscl t1out pout i/o-bus compare 3/2 t3cm1 t3cm2 t3c t3st modulator 3 demodu- lator 3 m2 control so tog3 int5 res cm31 t3i t3ex tog2 si sci t3m t3cs i/o-bus timer 2 ssi ssi cp3
49 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.3.1 timer/counter modes timer 3 has 6 timer modes and 6 modulator/demodulator modes. the mode is set via the timer 3 mode register t3m. in all these modes, the compare register and the compare-mode register belonging to it define the counter value for a compare match and the action of a compare match. a match of the cur- rent counter value with the content of one compare register triggers a counter reset, a timer 3 interrupt or the toggling of the output flip-flop. the compare mode registers t3m1 and t3m2 contain the mask bits for enabling or disabling these actions. the counter can also be enabled to execute single actions with one or both compare registers. if this mode is set the corresponding compare match event is generated only once after the counter start. most of the timer modes use their compare regi sters alternately. after the start has been acti- vated, the first comparison is carried out via the compare register 1, the second is carried out via the compare register 2, the third is carried out again via the compare register 1 and so on. this makes it easy to generate signals with constant periods and variable duty cycle or to generate signals with variable pulse and space widths. if single-action mode is set for one compare register, the comparison is always carried out after the first cycle via the other compare register. the counter can be started and stopped via the control register t3c. this register also controls the initial level of the output before a start. t3c contains the interrupt mask for a t3i input interrupt. via the timer 3 clock-select register, the internal or external clock source can be selected. this register also selects the active edge of the external input. an edge at the external input t3i can also generate an interrupt if the t3eim-bit is set and the timer 3 is stopped (t3r = 0) in the t3c register.
50 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-25. counter 3 stage the status of the timer as well as the occurrence of a compare match or an edge detect of the input signal is indicated by the status register t2st. this allows identification of the interrupt source because all these events share only one timer interrupt. timer 3 compares data values timer 3 has two 8-bit compare registers (t3co1, t3co2). the compare data value can be ?m? for each of the timer 3 compare registers. the compare data value for the compare registers is: m = x +1 0 x 255 timer 3 ? mode 1: timer/counter the selected clock from an internal or external source increments the 8-bit counter. in this mode, the timer can be used as event counter for external clocks at t3i or as a timer for generating interrupts and pulses at t3o. the counter value can be read by the software via the capture register. 8-bit comparator compare register 1 res capture register 8-bit counter compare register 2 control c31 c32 control t3sm1 nq d t3rm1 t3im1 t3tm1 tog2 t3i t3tm2 t3im2 t3rm2 t3sm2 nq d cl3 t3eim tog3 int5 cm31 cm32 : t3m1 : t3m2
51 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-26. counter reset with each compare match figure 5-27. counter reset with compare register 2 and toggle with start figure 5-28. single action of compare register 1 0 000123 5 1234 0 0123 12 t3r counter 3 cm31 int5 t3o 3 cm32 4 000123 567 4 0123 56 t3r counter 3 cm31 int5 t3o toggle by start t3o 89 cl3 cm32 0 012345678910012 counter 3 cm31 cm32 t3o 012012012012012012012 01201 toggle by start t3r
52 4593d?4bmcu?05/06 ATAR092-C/atar892-c timer 3 ? mode 2: timer/counter, extern al trigger restart and external capture (with t3i input) the counter is driven by an internal clock source. after starting with t3r, the first edge from the external input t3i starts the counter. the following edges at t3i load the current counter value into the capture register, resets the counter and restarts it. the edge can be selected by the pro- grammable edge decoder of the timer input stage. if single-action mode is activated for one or both compare registers the trigger signal restarts the single action. figure 5-29. externally triggered counte r reset and start combined with single-action mode timer 3 ? mode 3: timer/counter, internal trigger restart and internal capture (with tog2) the counter is driven by an internal or external (t3i) clock source. the output toggle signal of timer 2 resets the counter. the counter value before the reset is saved in the capture register. if single-action mode is activated for one both compare registers, the trigger signal restarts the sin- gle actions. this mode can be used for frequen cy measurements or as an event counter with a time gate (see combination mode 10). figure 5-30. event counter with time gate timer 3 ? mode 4: timer/counter the timer runs as a timer/counter in mode 1, but its output t3o is used as an output for the timer 2 output signal. timer 3 ? mode 5: timer/counter, extern al trigger restart and external capture (with t3i input) timer 3 runs as a timer/counter in mode 2, but it s output t3o is used as an output for the timer 2 output signal. 00000000123456 counter 3 t3ex cm31 cm32 78910012xxx012345678910 012xx t3r xx t3o 0012345678910 counter 3 tog2 t3cp- register 11 0 1 2 401 t3i 2 3 t3r capture value = 0 capture value = 11 capture value = 4
53 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.3.2 timer 3 modulator/demodulator modes timer 3 ? mode 6: carrier frequency burst modulation controlled by timer 2 output toggle flip-flop (m2) timer 3 counter is driven by an internal or external clock source. its compare- and compare mode registers must be programmed to generate the carrier frequency via the output toggle flip-flop. the output toggle flip-flop of timer 2 is used to enable or disable timer 3 output. timer 2 can be driven by the toggle output signal of ti mer 3 or any other clock source (see combina- tion mode 11). timer 3 ? mode 7: carrier frequency burst modulation controlled by ssi internal output (so) timer 3 counter is driven by an internal or external clock source. its compare- and compare mode registers must be programmed to generate the carrier frequency via the output toggle flip-flop. the output (so) of the ssi is used to enable or disable the timer 3 output. the ssi should be supplied with the toggle signal of timer 2 (see combination mode 12). timer 3 ? mode 8: fsk modulation with shift register data (so) the two compare registers are used for generating two different time intervals. the ssi internal data output (so) selects which compare register is used for the output frequency generation. a ?0? level at the ssi data output enables the compare register 1. a ?1? level enables compare reg- ister 2. the compare- and compare mode registers must be programmed to generate the two frequencies via the output toggle flip-flop. the ssi can be supplied with the toggle signal of timer 2. timer 3 counter is driven by an internal or external clock source. timer 2 counter is driven by counter 3 (tog3) (see also combination mode 13). figure 5-31. fsk modulation timer 3 ? mode 9: pulse-width modulation with the shift register the two compare registers are used for generating two different time intervals. the ssi internal data output (so) selects which compare register is used for the output pulse generation. in this mode both compare- and compare mode registers must be programmed for generating the two pulse-widths. it is also useful to enable the si ngle-action mode for extreme duty cycles. timer 2 is used as a baud rate generator and for the trigger restart of timer 3. the ssi must be supplied with a toggle signal of timer 2. the counter is driven by an internal or external clock source (see combination mode 7). 01234012340123 counter 3 cm31 cm32 so 401201201201201201201 20123 t3r 40 t3o 1 01 0
54 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-32. pulse-width modulation timer 3 ? mode 10: manchester demodulation/pulse-width demodulation for manchester demodulation, the edge detection stage must be programmed to detect each edge at the input. these edges are evaluated by the demodulator stage. the timer stage is used to generate the shift clock for the ssi. the compare register 1 match event defines the correct moment for shifting the state from input t3i as the decoded bit into shift register ? after that the demodulator waits for the next edge to synchronize the timer by a reset for the next bit. compare register 2 can also be used to detect a time-out error and handle it with an interrupt routine (also see combination mode 8). figure 5-33. timer 3 ? manchester demodulation 000000000 0000 counter 3 cm31 cm32 t3o 00000123456789 10 11 12 13 14 15 0 12345 tog2 67 8 1 9 11 12 10 14 13 0 2 3 14 15 0 0 0 1 sir so sco t3r 1011100 110 11 bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 synchronize manchester demodulation mode timer 3 mode t3ex si sr-data t3i cm3 = sci 100110
55 4593d?4bmcu?05/06 ATAR092-C/atar892-c timer 3 ? mode 11: bi-phase demodulation in the bi-phase demodulation mode, the timer operates like in manchester demodulation mode. the difference is that the bits are decoded via a to ggle flip-flop. this flip -flop samples the edge in the middle of the bit-frame and the compare register 1 match event shifts the toggle flip-flop out- put into the shift register (see also combined mode 9). figure 5-34. timer 3 ? bi-phase demodulation timer 3 ? mode 12: timer/counter with external capture mode (t3i) the counter is driven by an internal clock source and an edge at the external input t3i loads the counter value into the capture register. the edge can be selected with the programmable edge detector of the timer input stage. this mode can be used for signal and pulse measurements. figure 5-35. external capture mode 011 1 1 01 bit 0bit 1bit 2bit 3bit 4bit 5bit 6 synchronize biphase demodulation mode timer 3 mode t3ex q1 = si cm31 = sci sr-data 0000 t3i reset counter 3 101010 01234567891011 counter 3 t3cp- register 15 t3i t3r capture value = x capture value = 17 capture value = 35 01213141620 17 18 19 22 21 23 27 24 2526 29 28 30 34 31 32 33 36 35 37 41 38 39 40
56 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.3.3 timer 3 modulator for carrier frequency burst modulation if the output stage operates as a pulse-width modulator for the shift register the output can be stopped with stage 1 of timer 2. for this task, the timer mode 3 must be used and the prescaler must be supplied by the internal shift clock of the shift register. the modulator can be started with the start of the shift register (sir = 0) and stopped either by a shift register stop (sir = 1) or compare match event of stage 1 of timer 2. for this task, timer 2 must be used in mode 3 and the prescaler stage must be supplied by the internal shift clock of the shift register. figure 5-36. modulator 3 5.3.3.4 timer 3 demodulator for bi-phase-, manchester- and pulse-width-modulated signals the demodulator stage of timer 3 can be us ed to decode bi-phase-, manchester- and pulse-width-coded signals. figure 5-37. timer 3 ? demodulator 3 t3 set res t3o t3top omsk tog3 so ssi/ control m2 m3 mux t3m 0 1 2 3 timer 3 mode t3o 6 mux 1 7 mux 2 9 mux 3 other mux 0 demodulator 3 t3ex res cm31 counter 3 reset counter 3 control sci si t3i t3m
57 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.3.5 timer 3 mode register (t3m) note: 1. in this mode, the ssi can be used only as demodulator (8-bit nrz rising edge). all other ssi modes are not allowed. address: 'bhex - subaddress: '0'hex bit 3 bit 2 bit 1 bit 0 t3m t3m3 t3m2 t3m1 t3m0 reset value: 1111b t3m3 t imer 3 m ode select bit 3 t3m2 t imer 3 m ode select bit 2 t3m1 t imer 3 m ode select bit 1 t3m0 t imer 3 m ode select bit 0 table 5-13. timer 3 mode select bits mode t3m3 t3m2 t3m1 t3m0 timer 3 modes 11111timer/counter with a read access 21110 timer/counter, external capture and external trigger restart mode (t3i) 31101 timer/counter, internal capture and internal trigger restart mode (tog2) 41100 timer/counter mode 1 without output (t2o -> t3o) 51011 timer/counter mode 2 without output (t2o -> t3o) 61010burst modulation with timer 2 (m2) 71001burst modulation with shift register (so) 81000fsk modulation with shift register (so) 90111 pulse-width modulation with shift register (so) and timer 2 (tog2), internal trigger restart (sco) -> counter reset 100110 manchester demodulation/ pulse-width demodulation (1) (t2o -> t3o) 110101bi-phase demodulation (t2o -> t3o) 120100timer/counter with external capture mode (t3i) 130011not allowed 140010not allowed 150001not allowed 160000not allowed
58 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.3.6 timer 3 control register 1 (t3c) write 5.3.3.7 timer 3 status register 1 (t3st) read note: the status bits t3c1, t3c2 and t3ed will be reset after a read access to t3st. primary register address: ?c?hex - write bit 3 bit 2 bit 1 bit 0 write t3eim t3top t3ts t3r reset value: 0000b t3eim t imer 3 e dge i nterrupt m ask t3eim = 0, disables the interrupt when an edge event for timer 3 occurs (t3i) t3eim = 1, enables the interrupt when an edge event for timer 3 occurs (t3i) t3top t imer 3 t oggle o utput p reset t3top = 0, sets to ggle output (m3) to ?0? .............. ......t3top = 1, sets toggle output (m3) to ?1? .............. ......note: if t3r = 1, no output preset is possible t3ts t imer 3 t oggle with s tart ..t3ts = 0, timer 3 output is not toggled during the start ...... .......t3ts = 1, timer 3 output is toggled if started with t3r t3r t imer 3 r un ...... .......t3r = 0, timer 3 stop and reset ...... .......t3r = 1, timer 3 run primary register address: ?c?hex - read bit 3 bit 2 bit 1 bit 0 read ? t3ed t3c2 t3c1 reset value: x000b t3ed t imer 3 e dge d etect this bit will be set by the edge-dete ct logic of timer 3 input (t3i) t3c2 t imer 3 c ompare 2 this bit will be set when a match occurs between counter 3 and t3co2 t3c1 t imer 3 c ompare 1 this bit will be set when a match occurs between counter 3 and t3co1
59 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.3.8 timer 3 clock select register (t3cs) 5.3.3.9 timer 3 compare- and compare mode register timer 3 has two separate compare registers t3co1 and t3co2 for the 8-bit stage of timer 3. the timer compares the content of the compare register with the current counter value. if both match, it generates a signal. this signal can be used for the counter reset, to generate a timer interrupt, for toggling the output flip-flop, as ssi clock or as clock for the next counter stage. for each compare register, a compare-mode register exists. these registers contain mask bits to enable or disable the generation of an interrupt, a counter reset, or an output toggling with the occurrence of a compare match of the corresponding compare register. the mask bits for acti- vating the single-action mode can also be located in the compare mode registers. when assigned to the compare register a compare ev ent will be suppressed. address: ?b?hex - subaddress: ?1?hex bit 3 bit 2 bit 1 bit 0 t3cs t3e1 t3e0 t3cs1 t3cs0 reset value: 1111b t3e1 t imer 3 e dge select bit 1 t3e0 t imer 3 e dge select bit 0 table 5-14. external input edge select bits t3e1 t3e0 timer 3 input edge select (t3i) 11? 1 0 positive edge at t3i pin 0 1 negative edge at t3i pin 0 0 each edge at t3i pin t3cs1 t imer 3 c lock s ource select bit 1 t3cs0 t imer 3 c lock s ource select bit 0 table 5-15. select clock source bits t3cs1 tcs0 counter 3 input signal (cl3) 1 1 system clock (syscl) 1 0 output signal of timer 2 (pout) 0 1 output signal of timer 1 (t1out) 0 0 external input signal from t3i edge detect
60 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.3.10 timer 3 compare mode register 1 (t3cm1) t3cm1 contains the mask bits for the matc h event of counter 3 compare register 1 5.3.3.11 timer 3 compare mode register 2 (t3cm2) t3cm2 contains the mask bits for the matc h event of counter 3 compare register 2 address: ?b?hex - subaddress: ?2?hex bit 3 bit 2 bit 1 bit 0 t3cm1 t3sm1 t3tm1 t3rm1 t3im1 reset value: 0000b t3sm1 t imer 3 s ingle action m ask bit 1 t3sm1 = 0, disables single-action compare mode t3sm1 = 1, enables single-compare mode. after this bit is set, the compare register (t3co1) is used until the next compare match. t3tm1 t imer 3 compare t oggle action m ask bit 1 t3tm1 = 0, disables compare toggle t3tm1 = 1, enables compare toggle. a match of counter 3 with the compare register (t3co1) toggles t he output flip-flop (tog3). t3rm1 t imer 3 r eset m ask bit 1 t3rm1 = 0, disables counter reset t3rm1 = 1, enables counter reset. a ma tch of counter 3 with the compare register (t3co1) re sets the counter 3. t3im1 t imer 3 i nterrupt m ask bit 1 t3rm1 = 0, disables timer 3 interrupt for t3co1 register. t3rm1 = 1, enables timer 3 in terrupt for t3co1 register. address: ?b?hex - subaddress: ?3?hex bit 3 bit 2 bit 1 bit 0 t3cm2 t3sm2 t3tm2 t3rm2 t3im2 reset value: 0000b t3sm2 t imer 3 s ingle action m ask bit 2 t3sm2 = 0, disables single-action compare mode t3sm2 = 1, enables single-compare mode . after this bit is set, the compare register (t3co2) is used until the next compare match. t3tm2 t imer 3 compare t oggle action m ask bit 2 t3tm2 = 0, disables compare toggle t3tm2 = 1, enables compare toggle. a match of counter 3 with the compare register (t3co2) toggles th e output flip-flop (tog3). t3rm2 t imer 3 r eset m ask bit 2 t3rm2 = 0, disables counter reset t3rm2 = 1, enables counter reset. a match of counter 3 with the compare register (t3co2) resets the counter 3. t3im2 t imer 3 i nterrupt m ask bit 2 t3rm2 = 0, disables timer 3 interrupt for t3co2 register. t3rm2 = 1, enables timer 3 interrupt for t3co2 register.
61 4593d?4bmcu?05/06 ATAR092-C/atar892-c the compare registers and corresponding counter reset masks can be used to program the counter time intervals and the toggle masks can be used to program the output signal. the sin- gle-action mask can also be used in this mode. it starts operating after the timer starts with t3r. 5.3.3.12 timer 3 compare register 1 (t3co1) byte write 5.3.3.13 timer 3 compare register 2 (t3co2) byte write 5.3.3.14 timer 3 capture register the counter content can be read via the capture register. there are two ways to use the capture register. in modes 1 and 4, it is possible to read the current counter value directly out of the cap- ture register. in capture modes 2, 3, 5 and 12, a capture event like an edge at the timer 3 input or a signal from timer 2 stores the current count er value into the capture register. this counter value can be read from the capture register. 5.3.3.15 timer 3 capture register (t3cp) byte read address: ?b?hex - subaddress: ?4?hex high nibble second write cycle bit 7 bit 6 bit 5 bit 4 reset value: 1111b low nibble first write cycle bit 3 bit 2 bit 1 bit 0 reset value: 1111b address: ?b?hex - subaddress: ?5?hex high nibble second write cycle bit 7 bit 6 bit 5 bit 4 reset value: 1111b low nibble first write cycle bit 3 bit 2 bit 1 bit 0 reset value: 1111b address: ?b?hex - subaddress: ?4?hex high nibble first read cycle bit 7 bit 6 bit 5 bit 4 reset value: xxxxb low nibble second read cycle bit 3 bit 2 bit 1 bit 0 reset value: xxxxb
62 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.4 synchronous serial interface (ssi) 5.3.4.1 ssi features 2- and 3-wire nrz 2-wire mode, additional in ternal 2-wire link for mult i-chip packaging solutions with timer 2: ? bi-phase modulation ? manchester modulation ? pulse-width demodulation ? burst modulation with timer 3: ? pulse-width modulation (pwm) ? fsk modulation ? bi-phase demodulation ? manchester demodulation ? pulse-width demodulation ? pulse position demodulation 5.3.4.2 ssi peripheral configuration the synchronous serial interface (ssi) can be used either for serial communication with external devices such as eeproms, shift registers, display drivers, ot her microcontrollers, or as a means for generating and capturing on-chip serial streams of data. external data communication takes place via port 4 (bp4),a multi-functional po rt which can be software configured by writing the appropriate control word into the p4cr register. the ssi can be configured in any of the fol- lowing ways: 2-wire external interface for bi-directional data communication with one data terminal and one shift clock. the ssi uses port bp43 as a bi-direc tional serial data line (sd) and bp40 as a shift clock line (sc). 3-wire external interface for simultaneous input and output of serial data, with a serial input data terminal (si), a serial output data terminal (s o) and a shift clock (sc). the ssi uses bp40 as a shift clock (sc), while the serial data input (si) is applied to bp43 (configured in p4cr as input). serial output data (so) in this case is passed through to bp42 (configured in p4cr to t2o) via the timer 2 output stage (t2m2 configured in mode 6). timer/ssi combined modes ? the ssi used together with timer 2 or timer 3 is capable of per- forming a variety of data modulation and demodulation functions (see timer section). the modulating data is converted by the ssi into a cont inuous serial stream of data which is in turn modulated in one of the timer functional blocks. serial demodulated data can be serially cap- tured in the ssi and read by the controller. in the timer 3 modes 10 and 11 (demodulation modes) the ssi can only be used as demodulator. multi-chip link (mcl) ? the ssi can also be used as an interchip data interface for use in single package multi-chip modules or hybrids. for such applications, the ssi is provided with two dedi- cated pads (mcl_sd and mcl_sc) which act as a two-wire chip-to-chip link. the mcl can be activated by the mcl control bit. should th ese mcl pads be used by the ssi, the standard sd and sc pins are not required and the correspondi ng port 4 ports are available as conventional data ports.
63 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-38. block diagram of the synchronous serial interface 5.3.4.3 general ssi operation the ssi is comprised essentially of an 8-bit shif t register with two associated 8-bit buffers. the receive buffer (srb) for capturing the incoming se rial data and a transmit buffer (stb) for inter- mediate storage of data to be serially output. both buffers are directly accessible by software. transferring the parallel buffer data into and out of the shift register is controlled automatically by the ssi control, so that both single byte transfers or continuous bit streams can be supported. the ssi can generate the shift clock (sc) either from one of several on-chip clock sources or accept an external clock. the external shift clock is output on, or applied to the port bp40. selection of an external clock source is perfor med by the serial clock direction control bit (scd). in combinational modes, the required clock is selected by the corresponding timer mode. the ssi can operate in three data transfer m odes ? synchronous 8-bit shift mode, a 9-bit multi-chip link mode (mcl), containing 8-bit data and 1-bit acknowledge, and a corresponding 8-bit mcl mode without acknowledge. in both mcl modes the data transmission begins after a valid start condition and ends with a valid stop condition. external ssi clocking is not supported in these modes. the ssi should thus generate and have full control over the shift clock so that it can always be regarded as an mcl-bus master device. all directional control of the external data port used by the ssi is handled automatically and is dependent on the transmission direction set by the serial data direction (sdd) control bit. this control bit defines whether the ssi is currently operating in transmit (tx) mode or receive (rx) mode. serial data is organized in 8-bit telegrams which ar e shifted with the most significant bit first. in the 9-bit mcl mode, an additional acknowledge bit is appended to the end of the telegram for handshaking purposes (see mcl protocol). at the beginning of every telegram, the ssi control loads the transmit buffer into the shift register and proceeds immediately to shift data serially ou t. at the same time, incoming data is shifted into the shift register input. this incoming data is automatically loaded into the receive buffer when the complete telegram has been received. thus, data can be simultaneously received and transmitted if required. 8-bit shift register msb lsb shift_cl so sic1 sic2 sisc sc control stb srb si timer 2/timer 3 output int3 sc i/o-bus i/o-bus ssi-control tog2 pout t1out syscl so si mcl_sc sd mcl_sd transmit buffer receive buffer sci /2
64 4593d?4bmcu?05/06 ATAR092-C/atar892-c before data can be transferred, the ssi must first be activated. this is performed by means of the ssi reset control (sir) bit. all further operation then depends on the data directional mode (tx/rx) and the present status of the ssi buffer registers shown by the serial interface ready status flag (srdy). this srdy flag indicates the (empty/full) status of either the transmit buffer (in tx mode), or the receive buffer (in rx mode). the control logic ensures that data shifting is temporarily halted at any time, if the appropriate receive/transmit buffer is not ready (srdy = 0). the srdy status will then automatically be set ba ck to 1 and data shifting resumed as soon as the application software loads the new data into the transmit register (in tx mode) or frees the shift register by reading it into the receive buffer (in rx mode). a further activity status (act) bit indicates the present status of the serial communication. the act bit remains high for the duration of the serial telegram or if mcl stop or start conditions are currently being generated. both the current srdy and act status can be read in the ssi status register. to deactivate the ssi, the sir bit must be set to high. 5.3.4.4 8-bit synchronous mode figure 5-39. 8-bit synchronous mode in 8-bit synchronous mode, the ssi can operate as either a 2- or 3-wire interface (see ssi peripheral configuration). the serial data (sd) is received or transmitted in nrz format, synchro- nized to either the rising or falling edge of the shift clock (sc). the choice of clock edge is defined by the serial mode control bits (sm0,sm1). it should be noted that the transmission edge refers to the sc clock edge with which th e sd changes. to avoid clock skew problems, the incoming serial input data is shifted in with the opposite edge. when used together with one of the timer modulator or demodulator stages, the ssi must be set in the 8-bit synchronous mode 1. in rx mode, as soon as the ssi is activated (sir = 0), 8 shift clocks are generated and the incoming serial data is shifted into the shift register. this first telegram is automatically trans- ferred into the receive buffer and the srdy is set to 0 indicating that the receive buffer contains valid data. at the same time an interrupt (if enabled) is generated. the ssi then continues shift- ing the following 8-bit telegram. if, during this time the first telegram has been read by the controller, the second telegram will also be transferred in the same way into th e receive buffer and the ssi will continue clocking in the next te legram. should, however, the first telegram not have been read (srdy = 1), then the ssi will stop, temporarily holding the second telegram in the shift register until a certain point of time wh en the controller is able to service the receive buffer. in this way no data is lost or overwritten. sc sc data sd/to2 110 101 00 bit 7 bit 0 110 101 00 bit 7 bit 0 data: 00110101 (rising edge) (falling edge)
65 4593d?4bmcu?05/06 ATAR092-C/atar892-c deactivating the ssi (sir = 1) in mid-telegram will immediately stop the shift clock and latch the present contents of the shift register into the receive buffer. this can be used for clocking in a data telegram less than 8 bits in length. care should be taken to read out the final complete 8-bit data telegram of a multiple word message before deactivating the ssi (sir = 1) and terminating the reception. after te rmination, the shift r egister contents will overwr ite the receive buffer. figure 5-40. example of an 8-bit synchronous transmit operation figure 5-41. example of an 8-bit synchronous receive operation 7654321 0 765432107654321 0 msb lsb tx data 1 tx data 2 tx data 3 msb lsb msb lsb write stb (tx data 2) write stb (tx data 3) write stb (tx data 1) sc sd sir srdy interrupt (ifn = 0) interrupt (ifn = 1) act 43210 76543210 msb lsb rx data 1 rx data 2 rx data 3 msb lsb msb lsb read srb (rx data 2) read srb (rx data 3) read srb (rx data 1) sc sd sir srdy interrupt (ifn = 0) interrupt (ifn = 1) act 765 43210 765 7654
66 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.4.5 9-bit shift mode in the 9-bit shift mode, the ssi is able to handle the mcl protocol (described below). it always operates as an mcl master device, i.e., sc is always generated and output by the ssi. both the mcl start and stop conditions are automatically generated whenever the ssi is activated or deactivated by the sir-bit. in accordance with the mcl protocol, the output data is always changed in the clock low phase and shifted in on the high phase. before activating the ssi (sir = 0) and commencing an mcl dialog, the appropriate data direc- tion for the first word must be set using the sdd control bit. the state of this bit controls the direction of the data port (bp43 or mcl_sd). once started, the 8 data bits are, depending on the selected direction, either clocked into or out of the shift register. during the 9th clock period, the port direction is automatically switched over so that the corresponding acknowledge bit can be shifted out or read in. in transmit mode, the acknowledge bit received from the device is cap- tured in the ssi status register (tack) where it can be read by the controller. in receive mode, the state of the acknowledge bit to be returned to the device is predetermined by the ssi status register (rack). changing the direction mode (tx/rx) should not be performed during the transfer of an mcl telegram. one should wait until the end of the telegram which can be detected using the ssi interrupt (ifn = 1) or by interrogating the act status. once started, a 9-bit telegram will always run to completion and will not be prematurely termi- nated by the sir bit. so, if the sir-bit is set to 1 within the telegram, the ssi will complete the current transfer and terminate the dialog with an mcl stop condition. figure 5-42. example of mcl transmit dialog 7654321 76543210a msb lsb tx data 1 tx data 2 msb l sb wr i t e stb ( tx data 1 ) sc sd srdy act interrupt (ifn = 0) interrupt (ifn = 1) 0a wr i t e stb ( tx data 2 ) sir sdd start stop
67 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-43. example of mcl receive dialog 5.3.4.6 8-bit pseudo mcl mode in this mode, the ssi exhibits all the typical mcl operational features except for the acknowl- edge-bit which is never expected or transmitted. 5.3.4.7 mcl bus protocol the mcl protocol constitutes a simple 2-wire bi-directional communication highway via which devices can communicate control and data information. although the mcl protocol can support multi-master bus configurations, the ssi in mcl mode is intended for use purely as a master controller on a single master bus system. so all reference to multiple bus control and bus con- tention will be omi tted at this point. all data is packaged into 8-bit telegrams plus a trailing handshaking or acknowledge-bit. nor- mally the communication channel is opened with a so -called start condition, which initializes all devices connected to the bus. this is then follo wed by a data telegram, transmitted by the mas- ter controller device. this telegram usually co ntains an 8-bit address code to activate a single slave device connected onto the mcl bus. each slave receives this address and compares it with its own unique addre ss. the addressed slave de vice, if ready to receive data, will respond by pulling the sd line low during the 9th clock pu lse. this represents a so-called mcl acknowl- edge. the controller detecting this affirmative acknowledge then opens a connection to the required slave. data can then be passed back and forth by the master controller, each 8-bit tele- gram being acknowledged by the respective re cipient. the communication is finally closed by the master device when the slave device is put back into standby by applying a stop condition onto the bus. 7654321 76543210 a msb lsb tx data 1 rx data 2 msb l sb wr i t e stb ( tx data 1 ) sc sd srdy act interrupt (ifn = 0) interrupt (ifn = 1) 0a read sr b ( rx data 2 ) sir sdd start stop
68 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-44. mcl bus protocol 1 bus not busy (1) both data and clock lines remain high start data transfer (2) a high to low transition of the sd line while the clock (sc) is high defines a start condition stop data transfer (3) a low to high transition of the sd line while the clock (sc) is high defines a stop condition data valid (4) the state of the data line represents valid data when, after the start condition, the data line is stable for the duration of the high period of the clock signal acknowledge all address and data words are serially transmitted to and from the device in 8-bit words. the receiving device returns a zero on the data line during the ninth clock cycle to acknowledge a word receipt. figure 5-45. mcl bus protocol 2 (2) (1) (4) (4) (3) (1) start condition data valid data change data valid stop condition sc sd sc sd start 1n89 1st bit 8th bit ack stop
69 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.4.8 ssi interrupt the ssi interrupt int3 can be generated either by an ssi buffer register status (i.e., transmit buffer empty or receive buffer full), the end of ssi data telegram or on the falling edge of the sc/sd pins on port 4 (see p4cr). ssi interrupt selection is performed by the interrupt function control bit (ifn). the ssi interrupt is usually used to synchronize the software control of the ssi and inform the controller of the present ssi status. the port 4 interrupts can be used together with the ssi or, if the ssi itself is not required, as additional external interrupt sources. in either case this interrupt is capable of waking the controller out of sleep mode. to enable and select the ssi relevant interrupts use the ssi interrupt mask (sim) and the inter- rupt function (ifn) while port 4 interrupts are enabled by setting appropriate control bits in the p4cr register. 5.3.4.9 modulation and demodulation if the shift register is used together with timer 2 or timer 3 for modulation or demodulation pur- poses, the 8-bit synchronous mode must be used. in this case, the unused port 4 pins can be used as conventional bi-directional ports. the modulation and demodulation stages, if enabled, operate as soon as the ssi is activated (sir = 0) and cease when deactivated (sir = 1). due to the byte-orientated data control, the ssi (when running normally) generates serial bit streams which are submultiples of 8 bits. an ssi output masking (omsk) function permits, how- ever, the generation of bit streams of any length . the omsk signal is derived indirectly from the 4-bit prescaler of timer 2 and masks out a programmabl e number of unrequi red trailing data bits during the shifting out of the final data word in the bit stream. the number of non-masked data bits are defined by the value pre-programmed in the prescaler compare register. to use output masking, the modulator stop mode bit (msm) must be set to 0 before programming the final data word into the ssi transmit buffer. this in turn, enables shift clocks to the prescaler when this final word is shifted out. on reaching the compare value, the prescaler triggers the omsk signal and all following data bits are blanked. 5.3.4.10 internal 2-wire multi-chip link two additional on-chip pads (mcl_sc and mcl_ sd) for the sc and the sd line can be used as chip-to-chip links for multi-chip applications. these pads can be activated by setting the mcl-bit in the sisc register. figure 5-46. multi-chip link scl sda mcl_sc mcl_sd u505m ATAR092-C v dd bp40/sc bp10 bp43/sd bp13 multi-chip link v ss
70 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-47. ssi output masking function 5.3.4.11 serial interface control register 1 (sic1) 8-bit shift register msb lsb shift_cl so control si timer 2 output ssi-control so compare 2/1 4-bit counter 2/1 cl2/1 scl cm1 omsk sc tog2 pout t1out syscl /2 auxiliary register address: '9'hex bit 3bit 2bit 1bit 0 sic1 sir scd scs1 scs0 reset value: 1111b sir s erial i nterface r eset sir = 1, ssi inactive sir = 0, ssi active scd s erial c lock d irection scd = 1, sc line used as output scd = 0, sc line used as input note: this bit has to be set to '1' during the mcl mode and the timer 3 mode 10 or 11 scs1 s erial c lock source s elect bit 1 scs0 s erial c lock source s elect bit 0 note: with scd = '0' the bits scs1 and scs0 are insignificant table 5-16. serial clock sour ce select bits scs1 scs0 internal clock for ssi 1 1 syscl/2 10t1out/2 01pout/2 00tog2/2
71 4593d?4bmcu?05/06 ATAR092-C/atar892-c in transmit mode (sdd = 1) shifting starts only if the transmit buffer has been loaded (srdy = 1). setting sir-bit loads the contents of the shift register into the receive buffer (synchronous 8-bit mode only). in mcl modes, writing a 0 to sir generates a start condition and writing a 1 generates a stop condition. 5.3.4.12 serial interface control register 2 (sic2) note: sdd controls port directional control and defines the reset function for the srdy-flag auxiliary register address: ?a?hex bit 3bit 2bit 1bit 0 sic2 msm sm1 sm0 sdd reset value: 1111b msm m odular s top m ode msm = 1, modulator stop mode di sabled (output masking off) msm = 0, modulator stop mode enabled ( output masking on) - used in modulation modes for generating bit-streams whic h are not submultiples of 8 bits. sm1 s erial m ode control bit 1 sm0 s erial m ode control bit 0 table 5-17. serial mode control bits mode sm1 sm0 ssi mode 1 1 1 8-bit nrz-data changes with the rising edge of sc 2 1 0 8-bit nrz-data changes with the falling edge of sc 3 0 1 9-bit two-wire mcl mode 4 0 0 8-bit two-wire pseudo mcl mode (no acknowledge) sdd s erial d ata d irection sdd = 1, transmit mode ? sd line used as output (transmit data). srdy is set by a transmit buffer write access sdd = 0, receive mode ? sd line used as input (receive data). srdy is set by a receive buffer read access
72 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.4.13 serial interface status and control register (sisc) 5.3.4.14 serial transmit buffer (stb) ? byte write the stb is the transmit buffer of the ssi. the ssi transfers the transmit buffer into the shift reg- ister and starts shifting with the most significant bit. primary register address: ?a?hex bit 3 bit 2 bit 1 bit 0 write mcl rack sim ifn reset value: 1111b read ? tack act srdy reset value: xxxxb mcl m ulti- c hip l ink activation mcl = 1, multi-chip link disabled. this bit has to be set to 0 during transactions to/from th e eeprom of the atar892-c mcl = 0, connects sc and sd additionally to the internal multi-chip link pads rack r eceive ack nowledge status/control bit for mcl mode rack = 0, transmit acknowledge in next receive telegram rack = 1, transmit no acknowledge in last receive telegram tack t ransmit ack nowledge status/control bit for mcl mode tack = 0, acknowledge received in last transmit telegram tack = 1, no acknowledge received in last transmit telegram sim s erial i nterrupt m ask sim = 1, disable interrupts sim = 0, enable serial interrupt. an interrupt is generated. ifn i nterrupt f u n ction ifn = 1, the serial interrupt is generated at the end of the telegram ifn = 0, the serial interrupt is generated when the srdy goes low (i.e., buffer becomes empty/full in transmit/receive mode) srdy s erial interface buffer r ea dy status flag srdy = 1, in receive mode: receive buffer empty in transmit mode: transmit buffer full srdy = 0, in receive mode: receive buffer full in transmit mode: transmit buffer empty act transmission act ive status flag act = 1, transmission is active, i.e. , serial data transfer. stop or start conditions are currently in progress. act = 0, transmission is inactive primary register address: ?9?hex stb first write cycle bit 3 bit 2 bit 1 bit 0 reset value: xxxxb second write cycle bit 7 bit 6 bit 5 bit 4 reset value: xxxxb
73 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.4.15 serial receive buffer (srb) ? byte read the srb is the receive buffer of the ssi. the shift register clocks serial data in (most significant bit first) and the loads content into the receive buffer when the complete telegram has been received. 5.3.5 combination modes the utcm consists of two timers (timer 2 and timer 3) and a serial interface. there is a multi- tude of modes in which the timers and serial interface can work together. the 8-bit wide serial interface operates as a shif t register for modulation and demodulation. the modulator and demodulator units work together with the timers and shift the data bits into or out of the shift register. 5.3.5.1 combination mode timer 2 and ssi figure 5-48. combination timer 2 and ssi primary register address: ?9?hex srb first read cycle bit 7 bit 6 bit 5 bit 4 reset value: xxxxb second read cycle bit 3 bit 2 bit 1 bit 0 reset value: xxxxb 4-bit counter 2/1 res ovf1 compare 2/1 t2co1 pout cl2/2 dcg t2m1 p4cr 8-bit counter 2/2 res ovf2 compare 2/2 t2co2 t2cm timer 2 - control tog2 int4 bi-phase manchester modulator output mout t2o timer 2 modulator output-stage t2m2 so control t2c cl2/1 t2i syscl t1out tog3 scl i/o-bus 8-bit shift register msb lsb shift_cl so sic1 sic2 sisc scli control stb srb si output int3 i/o-bus ssi-control tog2 pout t1out syscl mcl_sc mcl_sd transmit buffer receive buffer cm1 i/o-bus pout so scl sc sd dcgo tog2
74 4593d?4bmcu?05/06 ATAR092-C/atar892-c combination mode 1: burst modulation ssi mode 1: 8-bit nrz and internal data so output to timer 2 modulator stage timer 2 mode 1, 2, 3 or 4: 8-bit compare counter with 4-bit programmable prescaler and dcg timer 2 output mode 3: duty cycle burst generator figure 5-49. carrier frequency burst modulation with the ssi internal data output combination mode 2: bi-phase modulation 1 ssi mode 1: 8-bit shift register internal data output (so) to timer 2 modulator stage timer 2 mode 1, 2, 3 or 4: 8-bit compare counter with 4-bit programmable prescaler timer 2 output mode 4: the modulator 2 of timer 2 modulates the ssi internal data output to bi-phase-code figure 5-50. bi-phase modulation 1 1 201201201201201201201201201201201201201 dcgo counter 2 tog2 so t2o counter = compare register (= 2) bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 bit 8 bit 9 bit 10 bit 11 bit 12 bit 13 tog2 sc so t2o 000 0 0011 0101 11 1 1 8-bit sr-data bit 7 bit 0 data: 00110101
75 4593d?4bmcu?05/06 ATAR092-C/atar892-c combination mode 3: manchester modulation 1 ssi mode 1: 8-bit shift register internal data output (so) to timer 2 modulator stage timer 2 mode 1, 2, 3 or 4: 8-bit compare counter with 4-bit programmable prescaler timer 2 output mode 5: the modulator 2 of timer 2 modulates the ssi internal data output to manchester-code figure 5-51. manchester modulation 1 combination mode 4: manchester modulation 2 ssi mode 1: 8-bit shift register internal data output (so) to timer 2 modulator stage timer 2 mode 3: 8-bit compare counter and 4-bit prescaler timer 2 output mode 5: the modulator 2 of timer 2 modulates the ssi data output to manchester-code the 4-bit stage can be used as a prescaler for the ssi to generate the stop signal for modulator 2. the ssi has a special mode to supply the prescaler with the shift clock. the control output signal (omsk) of the ssi is used as a stop signal for the modulator. figure 5-52 on page 76 shows an example for a 12-bit manchester telegram. tog2 sc so t2o 00 0 0011 0101 11 1 1 8-bit sr-data bit 7 bit 0 0 bit 7 bit 0 data: 00110101
76 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-52. manchester modulation 2 combination mode 5: bi-phase modulation 2 ssi mode 1: 8-bit shift register internal data output (so) to timer 2 modulator stage timer 2 mode 3: 8-bit compare counter and 4-bit prescaler timer 2 output mode 4: the modulator 2 of timer 2 modulates the ssi data output to bi-phase-code the 4-bit stage can be used as a prescaler for the ssi to generate the stop signal for modulator 2. the ssi has a special mode to supply the pre scaler via the shift clock. the control output sig- nal (omsk) of the ssi is used as a stop signal for the modulator. figure 5-53 shows an example for a 13-bit bi-phase telegram. figure 5-53. bi-phase modulation 2 000000001234012 0 c ount er 2/ 1 = c om pare r egi st er 2/ 1 (= 4) b it 7 b it 6 b it 5 b it 4 b it 3 b it 2 b it 1 b it 0 b it 7 b it 6 b it 5 b it 4 b it 3 b it 2 b it 1 b it 0 s c li b uffer full s ir s o s c m s m ti m er 2 m ode 3 s c l c ount er 2/ 1 o m s k t2o 3 00000000 1234 5 0 counter 2/1 = compare register 2/1 (= 5) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 scli buffer full sir so sc msm timer 2 mode 3 scl counter 2/1 omsk t2o 012
77 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.5.2 combination mode timer 3 and ssi figure 5-54. combination timer 3 and ssi combination mode 6: fsk modulation ssi mode 1: 8-bit shift register internal data output (so) to timer 3 timer 3 mode 8: fsk modulation with shift register data (so) the two compare registers are used to generate two varied time intervals. the ssi data output selects which compare register is used for the output frequency generation. a 0 level at the ssi data output enables the compare register 1 and a 1 level enables the compare register 2. the compare and compare mode registers must be programmed to generate the two frequencies via the output toggle flip flop. the ssi can be supplied with the toggle signal of timer 2 or any other clock source. timer 3 counter is driven by an internal or external clock source. figure 5-55. fsk modulation 1 8-bit counter 3 res compare 3/1 t3co1 t3cp t3co2 timer 3 - control t3o cl3 t3i t3ex syscl t1out pout i/o-bus compare 3/2 t3cm1 t3cm2 t3c t3st modulator 3 demodu- lator 3 m2 control so tog3 int5 res cm31 t3i t3ex si sc t3m t3cs cp3 8-bit shift register msb lsb shift_cl so sic1 sic2 sisc scli control stb srb si output int3 i/o-bus ssi-control tog2 pout t1out syscl si mcl_sc mcl_sd transmit buffer receive buffer sc sc si 01234012340120 counter 3 cm31 cm32 so 120120120120120120120 12340 t3r 12 t3o 3 01 0 40
78 4593d?4bmcu?05/06 ATAR092-C/atar892-c combination mode 7: pulse-width modulation (pwm) ssi mode 1: 8-bit shift register internal data output (so) to timer 3 timer 3 mode 9: pulse-width modulation with the shift register data (so) the two compare registers are used to generate two varied time intervals. the ssi data output selects which compare register is used for the output pulse generation. in this mode, both com- pare and compare mode registers must be programmed to generate the two pulse-widths. it is also useful to enable the single-action mode for extreme duty cycles. timer 2 is used as baud rate generator and for the triggered restart of timer 3. the ssi must be supplied with the toggle signal of timer 2. the counter is driven by an internal or external clock source. figure 5-56. pulse-width modulation combination mode 8: manchester demodulation/pulse-width demodulation ssi mode 1: 8-bit shift register internal data input (si) and the internal shift clock (sci) from the timer 3 timer 3 mode 10: manchester demodulation/pulse-width demodulation with timer 3 for manchester demodulation, the edge detection stage must be programmed to detect each edge at the input. these edges are evaluated by the demodulator stage. the timer stage is used to generate the shift clock for the ssi. a compare register 1 match event defines the correct moment for shifting the state from the input t3i as the decoded bit into shift register. after that, the demodulator waits for the next edge to synchronize the timer by a reset for the next bit. the compare register 2 can be used to detect a time error and handle it with an interrupt routine. before activating the demodulator mode the timer and the demodulator stage must be synchro- nized with the bit-stream. the manchester-code timing consists of parts with the half bit-length and the complete bit-length. a synchronization routine must start the demodulator after an inter- val with the comple te bit-length. the counter can be driven by any internal clock source. the output t3o can be used by timer 2 in this mode. the manchester decoder can also be used for pulse-width demodulation. the input must be programmed to detect the positive edge. the demodulator and timer must be synchro- nized with the leading edge of the pulse. after that a counter match with the compare register 1 shifts the state at the input t3i into the shift register. the next positive edge at the input restarts the timer. 000000000 0000 counter 3 cm31 cm32 t3o 00000123456789 10 11 12 13 14 15 0 12345 tog2 67 8 1 9 11 12 10 14 13 0 2 3 14 15 0 0 0 1 sir so sco t3r
79 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-57. manchester demodulation combination mode 9: bi-phase demodulation ssi mode 1: 8-bit shift register internal data input (si) and the internal shift clock (sci) from timer 3 timer 3 mode 11: bi-phase demodulation with timer 3 in the bi-phase demodulation mode the timer works like in the manchester demodulation mode. the difference is that the bits are decoded with t he toggle flip-flop. this flip-flop samples the edge in the middle of the bit-frame and the compare register 1 match event shifts the toggle flip-flop output into the shift register. before activating the demodulation the timer and the demodulation stage must be synchronized with th e bit-stream. the bi- phase code timing con- sists of parts with the half bit-length and the complete bit-length. the synchronization routine must start the demodulator after an interval with the complete bit-length. the counter can be driven by any internal clock source and the output t3o can be used by timer 2 in this mode. figure 5-58. bi-phase demodulation 1011100 110 11 bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 synchronize manchester demodulation mode timer 3 mode t3ex si sr-data t3i cm3 = sci 100110 011 1 1 01 bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 synchronize bi-phase demodulation mode timer 3 mode t3ex q1 = si cm31 = sci sr-data 0000 t3i reset counter 3 101010
80 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.5.3 combination mode timer 2 and timer 3 figure 5-59. combination timer 3 and timer 2 combination mode 10: frequency measurement or event counter with time gate timer 2 mode 1/2: 12-bit compare counter/8-bit compare counter and 4-bit prescaler timer 2 output mode 1/6: timer 2 compare match toggles (tog2) to timer 3 timer 3 mode 3: timer/counter; internal trigger restart and internal capture (with timer 2 tog2-signal) the counter is driven by an external (t3i) cloc k source. the output signal (tog2) of timer 2 resets the counter. the counter value before re set is saved in the capture register. if sin- gle-action mode is activated for one or both com pare registers, the trigger signal also restarts the single action. this mode can be used for frequency measurements or as event counter with time gate. 8-bit counter 3 res compare 3/1 t3co1 t3cp t3co2 timer 3 - control t3o cl3 t3i t3ex syscl t1out pout i/o-bus compare 3/2 t3cm1 t3cm2 t3c t3st modulator 3 demodu- lator 3 control so tog3 int5 res cm31 t3i t3ex tog2 si sci ssi cp3 4-bit counter 2/1 res ovf1 compare 2/1 t2co1 cm1 pout ssi cl2/2 dcg t2m1 p4cr 8-bit counter 2/2 res ovf2 compare 2/2 t2co2 t2cm tog2 int4 bi-phase manchester modulator output mout m2 t2o timer 2 modulator 2 output-stage t2m2 control (re, fe, sco, omsk) ssi t2c cl2/1 tog3 syscl t1out scl timer 2 - control m2 t3cs t3m pout dcgo so t2i i/o-bus i/o-bus
81 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-60. frequency measurement figure 5-61. event counter with time gate combination mode 11: burst modulation 1 timer 2 mode 1/2: 12-bit compare counter/8-bit compare counter and 4-bit prescaler timer 2 output mode 1/6: timer 2 compare match toggles the output flip-flop (m2) to timer 3 timer 3 mode 6: carrier frequency burst modulation controlled by timer 2 output (m2) timer 3 counter is driven by an internal or external clock source. its compare and compare mode registers must be programmed to generate the carrier frequency with the output toggle flip-flop. the output toggle flip-flop (m2) of timer 2 is used to enable and disable timer 3 output. timer 2 can be driven by the toggle output sign al of timer 3 (tog3) or any other clock source. figure 5-62. burst modulation 1 00123456789 10 counter 3 tog2 t3cp- register t3i t3r capture value = 0 capture value = 17 capt. value = 18 1112 131415 16 17 123456789 101112 13141516 1718 0 0123 45 0012345678910 counter 3 tog2 t3cp- register 11 0 1 2 401 t3i 2 3 t3r capture value = 0 capture value = 11 capture value = 4 0101234501012345010123450101 50101 50101 50101 50101 50101 50101 50101 50101 50101 30 1 2 3 3 0 1 3 2 cl3 counter 3 cm1 cm2 tog3 m3 counter 2/2 tog2 m2 t3o
82 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.5.4 combination mode timer 2, timer 3 and ssi figure 5-63. combination timer 2, timer 3 and ssi 8-bit counter 3 res compare 3/1 t3co1 t3cp t3co2 timer 3 - control t3o cl3 t3i t3ex syscl t1out pout i/o-bus compare 3/2 t3cm1 t3cm2 t3c t3st modulator 3 demodu- lator 3 control so tog3 int5 res cm31 t3i t3ex tog2 si sci ssi cp3 4-bit counter 2/1 res ovf1 compare 2/1 t2co1 cm1 pout cl2/2 dcg t2m1 p4cr 8-bit counter 2/2 res ovf2 compare 2/2 t2co2 t2cm tog2 int4 bi-phase manchester modulator output mout m2 t2o timer 2 modulator 2 output-stage t2m2 control (re, fe, sco, omsk) t2c cl2/1 tog3 syscl t1out scl timer 2 - control m2 t3cs t3m pout dcgo so t2i i/o-bus i/o-bus 8-bit shift register msb lsb shift_cl so sic1 sic2 sisc scli control stb srb si output int3 i/o-bus ssi-control tog2 pout t1out syscl mcl_sc mcl_sd transmit buffer receive buffer sc si scl
83 4593d?4bmcu?05/06 ATAR092-C/atar892-c combination mode 12: burst modulation 2 ssi mode 1: 8-bit shift register internal data output (so) to timer 3 timer 2 output mode 2: 8-bit compare counter and 4-bit prescaler timer 2 output mode 1/6: timer 2 compare match toggles (tog2) to the ssi timer 3 mode 7: carrier frequency burst modulation controlled by the internal output (so) of ssi the timer 3 counter is driven by an internal or external clock source. its compare and compare mode registers must be programmed to generate the carrier frequency with the output toggle flip-flop (m3). the internal data output (so) of the ssi is used to enable and disable timer 3 out- put. the ssi can by supplied wit h the toggle signal of timer 2. figure 5-64. burst modulation 2 combination mode 13: fsk modulation ssi mode 1: 8-bit shift register internal data output (so) to timer 3 timer 2 output mode 3: 8-bit compare counter and 4-bit prescaler timer 2 output mode 1/6: timer 2 4-bit compare match signal (pout) to the ssi timer 3 mode 8: fsk modulation with shift register data output (so) the two compare registers are used to generate two different time intervals. the ssi data output selects which compare register is used for the output frequency generation. a 0 level at the ssi data output enables the compare register 1 and a 1 level enables the compare register 2. the compare- and compare mode registers must be programmed to generate the two frequencies via the output toggle flip-flop. the ssi can be supplied with the toggle signal of timer 2 or any other clock source. timer 3 counter is driven by an internal or ex ternal clock source. 0101234501012345010123450101 50101 50101 50101 50101 50101 50101 50101 50101 50101 30 1 2 3 3 0 1 3 2 cl3 counter 3 cm31 cm32 tog3 m3 counter 2/2 tog2 so t3o
84 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 5-65. fsk modulation 6. atar892-c the atar892-c is a multi-chip device which of fers a combination of a marc4-based microcon- troller and a serial e2prom data memory in a single package. the ATAR092-C is used as a mircocontroller a nd the u5005m is used as serial e2prom. two internal lines can be used as chip-to-chip link in a single package. the maximum internal data communication frequency between the ATAR092-C and the u505m over the chip link (mcl_sc and mcl_sd) is f sc_mcl = 500 khz. the microcontroller and the eeprom portions of th is multi-chip device are equivalent to their respective individual component chips, except for the electrical specification. 6.1 internal 2-wire multi-chip link two additional on-chip pads (mcl_sc and mcl_sd ) for the sc and the sd lines can be used as chip-to-chip links for multi-chip applications. these pads can be activated by setting the mcl-bit in the sisc register. figure 6-1. multi-chip link 01234012340123 counter 3 cm31 cm32 so 401201201201201201201 20123 t3r 40 t3o 1 01 0 scl sda mcl_sc mcl_sd u505m ATAR092-C v dd bp40/sc bp10 bp43/sd bp13 multi-chip link v ss
85 4593d?4bmcu?05/06 ATAR092-C/atar892-c 6.2 u505m eeprom the u505m is a 512-bit eeprom in ternally organized as 32 x 16 bits. the programming voltage as well as the write-cycle timing is generated on- chip. the u505m features a serial interface allowing operation on a simple two-wire bus with an mcl protocol. its low power consumption makes it well suited fo r battery applications. figure 6-2. block diagram eeprom 6.2.1 serial interface the u505m has a two-wire serial interface to the microcontroller for read and write accesses to the eeprom. the u505m is consider ed to be a slave in all these applications. that means, the controller has to be the master that initiates the data transfer and provides the clock for transmit and receive operations. the serial interface is controlled by the atar892-c microcontroller which generates the serial clock and controls the access via the scl-line and sda-line. scl is used to clock the data into and out of the device. sda is a bi-directional line th at is used to transfer data into and out of the device. the following protocol is used for data transfers. 16-bit read/write buffer address control 8-bit data register eeprom 32 x 16 hv-generator timing control mode control i/o control scl v dd v ss sda
86 4593d?4bmcu?05/06 ATAR092-C/atar892-c 6.2.1.1 serial protocol data states on the sda-line change only while scl is low. changes on the sda line while scl is high are interpreted as start or stop conditions. a start condition is defined as a high to lo w transition on the sda-line while the scl-line is high. a stop condition is defined as a low to high transition on the sda-line while the scl-line is high. each data transfer must be initialized with a start condition and terminated with a stop condition. the start condition wakes the device from standby mode and the stop condition returns the device to standby mode. a receiving device generates an acknowledge (a) after the reception of each byte. this requires an additional clock pulse, generated by the master. if the reception was successful the receiving master or slave device pulls do wn the sda-line during that clock cycle. if an acknowledge is not detected (n) by the interface in tr ansmit mode, it will terminate further data transmissions and go into receive mode. a master device must finish its read operation by a non-acknowledge and then send a stop condition to bring the device into a known state. figure 6-3. mcl protocol before the start condition and after the stop condition the device is in standby mode and the sda line is switched as input with pull-up resistor. the control byte that follows the start cond ition determines the following operation. it consists of the 5-bit row address, 2 mode contro l bits and the read/ nwrite bit that is used to control the direction of the following transfer. a 0 defines a write access and a 1 a read access. 6.2.1.2 control byte format start condition data valid data change data/ acknowledge valid stop condition scl sda stand-by stand-by eeprom address mode control bits read/ nwrite starta4a3a2a1a0c1c0r/nwackn start control byte ackn data byte ackn data byte ackn stop
87 4593d?4bmcu?05/06 ATAR092-C/atar892-c 6.2.2 eeprom the eeprom has a size of 512 bi ts and is organized as 32 x 16-bit matrix. to read and write data to and from the eeprom the serial interface must be used. the interface supports one and two byte write accesses and one to n-byte read accesses to the eeprom. 6.2.2.1 eeprom ? operating modes the operating modes of the eeprom are defined via the control byte. the control byte contains the row address, the mode control bits and the read/not-write bit that is used to control the direc- tion of the following transfer. a 0 defines a write access and a 1 a read access. the five address bits select one of the 32 rows of the eeprom memory to be accessed. for all accesses the complete 16-bit word of the selected row is loaded into a buffer. the buffer must be read or over- written via the serial interface. the two mode control bits c0 and c1 define in which order the accesses to the buffer are performed: high byte ? low byte or low byte ? high byte. the eeprom also supports autoincrement and autodecrement read operations. after sending the start address with the corresponding mode, consecutive memory cells can be read row by row without transmission of the row addresses. two special control bytes enabl e the complete initialization of eeprom with 0 or with 1. 6.2.2.2 write operations the eeprom allows 8-bit and 16-bit write operat ions. a write access starts with the start condition followed by a write control byte and one or two data bytes from the master. it is com- pleted via the stop condition from the master after the acknowledge cycle. the programming cycle consists of an erase cycle (write ?0?) and th e write cycle (write ?1?). both cycles together take about 10 ms. 6.2.2.3 acknowledge polling if the eeprom is busy with an internal write cycle, all inputs are disabled a nd the eeprom will not acknowledge until the write cycle is finished. this can be used to detect the end of the write cycle. the master must perform acknowledge po lling by sending a start condition followed by the control byte. if the device is still busy with the write cycle, it will not return an acknowledge and the master has to generate a stop condition or perform further acknowledge polling sequences. if the cycle is complete, it returns an acknowledge and the master can proceed with the next read or write cycle. 6.2.2.4 write one data byte 6.2.2.5 write two data bytes 6.2.2.6 write control byte only start control byte a data byte 1 a stop start control byte a data byte 1 a data byte 2 a stop start control byte a stop
88 4593d?4bmcu?05/06 ATAR092-C/atar892-c 6.2.2.7 write control bytes a: acknowledge; hb: high byte; lb: low byte; r: row address 6.2.2.8 read operations the eeprom allows byte, word and current address read operations. the read operations are initiated in the same way as write operations. every read access is initiated by sending the start condition followed by the control byte which contains the address and the read mode. when the device has received a read command, it returns an acknowledge, loads the addressed word into the read/write buffer and sends the selected data byte to the master. the master has to acknowledge the received byte if it wants to proceed with the read operation. if two bytes are read out from the buffer the device increments respectively, decrements the word address auto- matically and loads the buffer with the next word. the read mode bits determines if the low or high byte is read from the buffer first and if the word address is incremented or decremented for the next read access. if the memory address limit is reached, the data word address will ?roll over? and the sequential read will continue. the master can terminate the read operation after every byte by not responding with an acknowledge (n) and by issuing a stop condition. 6.2.2.9 read one data byte 6.2.2.10 read two data bytes 6.2.2.11 read n data bytes msb lsb write low byte first a4 a3 a2 a1 a0 c1 c0 r/nw row address 0 1 0 byte order lb(r) hb(r) msb lsb write high byte first a4 a3 a2 a1 a0 c1 c0 r/nw row address 1 0 0 byte order hb(r) lb(r) start control byte a data byte 1 n stop start control byte a data byte 1 a data byte 2 n stop start control byte a data byte 1 a data byte 2 a - - - data byte n n stop
89 4593d?4bmcu?05/06 ATAR092-C/atar892-c 6.2.2.12 read control bytes a: acknowledge, n: no acknowledge; hb: high byte; lb: low byte, r: row address 6.2.2.13 initialization a fter a reset condition the eeprom with the serial interface has its own reset circuitry. in systems with microcontrol- lers that have their own reset circuitry for power-on reset, watchdog reset or brown-out reset, it may be necessary to bring the u505m into a known state independent of its internal reset. this is performed by writing: to the serial interface. if the u505m acknowledges this sequence it is in a defined state. it may be necessary to perform this sequence twice. msb lsb read low byte first, address increment a4 a3 a2 a1 a0 c1 c0 r/nw row address 0 1 1 byte order lb(r) hb(r) lb(r+1) hb(r+1) - - - lb(r+n) hb(r+n) msb lsb read high byte first, address decrement a4 a3 a2 a1 a0 c1 c0 r/nw row address 1 0 1 byte order hb(r) lb(r) hb(r-1) lb(r-1) - - - hb(r-n) lb(r-n) start control byte a data byte 1 n stop
90 4593d?4bmcu?05/06 ATAR092-C/atar892-c 7. absolute maximum ratings voltages are given relative to v ss. stresses beyond those listed under ?absolute maximum ratings? may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions beyond t hose indicated in the operational sections of this specification is not implied. exposure to absolute maximum rati ng conditions for extended periods may affect device reliability . all inputs and outputs are protected against high electrostatic vo ltages or electric fields. however, precautions to minimize t he build-up of electrostatic charges during handling are recommended. reliabilit y of operation is enhanced if unused inputs are connected to a n appropriate logic voltage level (e.g., v dd ). parameters symbol value unit supply voltage v dd ?0.3 to +6.5 v input voltage (on any pin) v in v ss ? 0.3 v in v dd + 0.3 v output short circuit duration t short indefinite s operating temperature range t amb ?40 to +105 c storage temperature range t stg ?40 to +130 c soldering temperature (t 10 s) t sld 260 c 8. thermal resistance parameter symbol value unit thermal resistance (sso20) r thja 140 k/w 9. dc operating characteristics v ss = 0v, t amb = ?40c to +105c unless otherwise specified. parameters test conditions symbol min. typ. max. unit power supply operating voltage at v dd v dd v por 6.5 v active current cpu active f syscl = 1 mhz v dd = 1.8 v v dd = 3.0 v v dd = 6.5 v i dd 200 300 700 400 a a a power down current (cpu sleep, rc oscillator active, 4-mhz quartz oscillator active) f syscl = 1 mhz v dd = 1.8 v v dd = 3.0 v v dd = 6.5 v i pd 40 70 200 180 a a a sleep current (cpu sleep, 32-khz quartz oscillator active, 4-mhz quartz oscillator inactive) v dd = 1.8 v v dd = 3.0 v v dd = 6.5 v i sleep 0.4 0.6 0.8 1.3 1.8 a a a sleep current (cpu sleep, 32-khz quartz oscillator inactive, 4-mhz quartz oscillator inactive) v dd = 1.8 v for ATAR092-C v dd = 3.0 v for ATAR092-C v dd = 6.5 v for ATAR092-C v dd = 6.5 v for atar892-c i sleep 0.1 0.3 0.5 0.6 0.5 0.8 1.0 a a a a pin capacitance any pin to v ss c l 710pf note: the pin bp20/nte has a static pull-up resistor during the reset-phase of the microcontroller
91 4593d?4bmcu?05/06 ATAR092-C/atar892-c power-on reset threshold voltage por threshold voltage bot = 1 v por 1.6 1.7 1.8 v por threshold voltage bot = 0 v por 1.85 2.0 2.15 v por hysteresis v por 50 mv voltage monitor threshold voltage vm high threshold voltage v dd > vm, vms = 1 v mthh 3.0 3.25 v vm high threshold voltage v dd < vm, vms = 0 v mthh 2.75 3.0 v vm middle threshold voltage v dd > vm, vms = 1 v mthm 2.6 2.8 v vm middle threshold voltage v dd < vm, vms = 0 v mthm 2.4 2.6 v vm low threshold voltage v dd > vm, vms = 1 v mthl 2.2 2.4 v vm low threshold voltage v dd < vm, vms = 0 v mthl 2.0 2.2 v external input voltage vmi v dd = 3 v, vms = 1 v vmi 1.3 1.4 v vmi v dd = 3 v, vms = 0 v vmi 1.2 1.3 v all bi-directional ports input voltage low v dd = 1.8 to 6.5 v v il v ss 0.2 v dd v input voltage high v dd = 1.8 to 6.5 v v ih 0.8 v dd v dd v input low current (switched pull-up) v dd = 2.0v, v dd = 3.0v, v il = v ss v dd = 6.5v i il ?2 ?10 ?50 ?4 ?20 ?100 ?12 ?40 ?200 a a a input high current (switched pull-down) v dd = 2.0v, v dd = 3.0v, v ih = v dd v dd = 6.5v i ih 2 10 50 4 20 100 12 40 200 a a a input low current (static pull-up) v dd = 2.0v v dd = 3.0v, v il = v ss v dd = 6.5v i il ?20 ?80 ?300 ?50 ?160 ?600 ?100 ?320 ?1200 a a a input low current (static pull-down) v dd = 2.0v v dd = 3.0v, v ih = v dd v dd = 6.5v i ih 20 80 300 50 160 600 100 320 1200 a a a input leakage current v il = v ss i il 100 na input leakage current v ih = v dd i ih 100 na output low current v ol = 0.2 v dd v dd = 2.0v v dd = 3.0v v dd = 6.5v i ol 0.6 3 8 1.2 5 15 2.5 8 22 ma ma ma output high current v oh = 0.8 v dd v dd = 2.0v v dd = 3.0v v dd = 6.5v i oh ?0.6 ?3 ?8 ?1.2 ?5 ?16 ?2.5 ?8 ?24 ma ma ma 9. dc operating characteristics (continued) v ss = 0v, t amb = ?40c to +105c unless otherwise specified. parameters test conditions symbol min. typ. max. unit note: the pin bp20/nte has a static pull-up resistor during the reset-phase of the microcontroller
92 4593d?4bmcu?05/06 ATAR092-C/atar892-c 10. ac characteristics supply voltage v dd = 1.8v to 6.5v, v ss = 0v, t amb = 25c unless otherwise specified. parameters test conditions symbol min. typ. max. unit operation cycle time system clock cycle v dd = 1.8 to 6.5 v t amb = ?40 to +105 c t syscl 500 4000 ns v dd = 2.4 to 6.5 v t amb = ?40 to +105 c t syscl 250 4000 ns timer 2 input timing pin t2i timer 2 input clock f t2i 5mhz timer 2 input low time rise/fall time < 10 ns t t2il 100 ns timer 2 input high time rise/fall time < 10 ns t t2ih 100 ns timer 3 input timing pin t3i timer 3 input clock f t3i syscl/2 mhz timer 3 input low time rise/fall time < 10 ns t t3il 2t syscl ns timer 3 input high time rise/fall time < 10 ns t t3ih 2t syscl ns interrupt request input timing interrupt request low time rise/fall time < 10 ns t irl 100 ns interrupt request high time rise/fall time < 10 ns t irh 100 ns external system clock exscl at osc1, ecm = en rise/fall time < 10 ns f exscl 0.5 4 mhz exscl at osc1, ecm = di rise/fall time < 10 ns f exscl 0.02 4 mhz input high time rise/fall time < 10 ns t ih 0.1 s reset timing power-on reset time v dd > v por t por 1.5 5 ms rc oscillator 1 frequency f rcout1 3.8 mhz stability v dd = 2.0 to 6.5 v t amb = ?40 to +105 c ? f/f 50 % rc oscillator 2 ? external resistor frequency r ext = 170 k ? f rcout2 4mhz stability v dd = 2.0 to 6.5 v t amb = ?40 to +85 c ? f/f 15 % stabilization time t s 10 s 4-mhz crystal oscillator (operating range v dd = 2.2v to 6.5v) frequency f x 4mhz start-up time t sq 5ms stability ? f/f ?10 +10 ppm integrated input/output capacitances (mask programmable) c in /c out programmable in steps of 0.63 nf c in c out 0 0 20 20 pf pf note: endurance and data retention independe nt and separately characterized.
93 4593d?4bmcu?05/06 ATAR092-C/atar892-c 32-khz crystal oscillator (operating range v dd = 2.0v to 6.5v) frequency f x 32.768 khz start-up time t sq 0.5 s stability ? f/f ?10 +10 ppm integrated input/output capacitances (mask programmable) c in /c out programmable in steps of 2pf c in c out 0 0 20 20 pf pf external 32-khz crystal parameters crystal frequency f x 32.768 khz serial resistance rs 30 50 k ? static capacitance c 0 1.5 pf dynamic capacitance c1 3 ff external 4-mhz crystal parameters crystal frequency f x 4.0 mhz serial resistance rs 40 150 ? static capacitance c 0 1.4 3 pf dynamic capacitance c1 3 ff eeprom operating current during erase/write cycle i wr 600 1300 a endurance (1) erase-/write cycles at 25c at 60c at 85c at 105c e d 500,000 200,000 100,000 50,000 1,000,000 cycles data erase/write cycle time t dew 912ms data retention time (1) at 25c at 105c t dr t dr 10 1 years years power-up to read operation t pur 0.2 ms power-up to write operation t puw 0.2 ms serial interface scl clock frequency f sc_mcl 100 500 khz 10. ac characteristics (continued) supply voltage v dd = 1.8v to 6.5v, v ss = 0v, t amb = 25c unless otherwise specified. parameters test conditions symbol min. typ. max. unit note: endurance and data retention independe nt and separately characterized.
94 4593d?4bmcu?05/06 ATAR092-C/atar892-c 10.1 recommendations for the 32-khz crystal oscillator 10.2 recommended values for integrated input/output capacit ances (mask option) c leff : effective load capacitance of the crystal for the nominal frequency of 32678 hz c opt : recommended value for the integrated capacitance to meet, together with the parasitic pin capacitance, the related c leff . 10.3 crystal characteristics figure 10-1. crystal equivalent circuit table 10-1. recommended parameters for 32-khz crystals (for example microcrystal ms1v, daishinku sm-14j) series resistance load capaci tance maximum load capacitance r smax = 35 k ? 8 pf < c leff > 10 pf 12 pf r smax = 50 k ? 7 pf < c leff > 9 pf 10 pf r smax = 70 k ? , typically 50 k ? 6 pf < c leff > 7 pf 8 pf c leff (pf)6 7 8 9 101112 c opt (pf) 3.8 5.6 7.5 10 11.9 13.8 15.6 l c 1 r s c 0 oscin oscout equivalent circuit sclin sclout
95 4593d?4bmcu?05/06 ATAR092-C/atar892-c 11. diagrams figure 11-1. active supply current versus frequency figure 11-2. active supply current versus v dd figure 11-3. power-down supply current versus frequency 0.0 0.5 1.0 1.5 2.0 2.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 f sysclk (mhz) i ddact (ma) t amb = -25c v dd = 6.5 v 5 v 3 v 2 v 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) i ddact (ma) t amb = 125c -40c 25c f sysclk = 1 mhz 0 50 100 150 200 250 300 350 400 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 f sysclk (mhz) i pd (a) t amb = -25c v dd = 6.5 v 5 v 3 v 2 v 4 v
96 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 11-4. power-down supply current versus v dd figure 11-5. sleep current versus t amb ? ATAR092-C figure 11-6. sleep current versus t amb ? atar892-c 0 20 40 60 80 100 120 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) i pd (a) f sysclk = 500 khz t amb = 25c 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 -40 -20 0 20 40 60 80 100 120 t amb (c) i ddsleep ( a) v dd = 6.5 v 3 v 5 v 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 -40 -20 0 20 40 60 80 100 120 t amb (c) i ddsleep ( a) v dd = 6.5 v 3 v 5 v
97 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 11-7. internal rc frequency versus v dd figure 11-8. internal rc frequency versus t amb figure 11-9. external rc frequency versus v dd 2.0 2.5 3.0 3.5 4.0 4.5 5.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) f rc_int (mhz) 105c 25c t amb = -40c 2. 0 2. 5 3. 0 3. 5 4. 0 4. 5 5. 0 -40 -20 0 20 40 60 80 100 120 t am b (c ) f r c _i n t (m h z) 2 v 2 v 2. 0 2. 5 3. 0 3. 5 4. 0 4. 5 5. 0 -40-200 20406080100120 t am b (c ) f r c _i n t (m h z) 2 v 3 v v d d = 6. 5 v 3.4 3.6 3.8 4.0 4.2 4.4 4.6 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) text rext = 47k tex t 3.4 3.6 3.8 4.0 4.2 4.4 4.6 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) f rc_ext (mhz) 105c r ext = 170 k ? t amb = -40c 25c
98 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 11-10. external rc frequency versus t amb figure 11-11. system clock versus v dd figure 11-12. external rc frequency versus r ext 3.4 3.6 3.8 4.0 4.2 4.4 4.6 -40 -20 0 20 40 60 80 100 120 t amb (c) f rc_ext (mhz) r ext = 170 k ? 2 v 3 v v dd = 6.5 v 0.01 0.10 1.00 10.00 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) f sysclk (mhz) sysclkmax sysclkmin 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 100 150 200 250 300 350 400 r ext (kohm) f rc_ext (mhz) t amb = 25c v dd = 3 v max. min. typ.
99 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 11-13. pull-up resistor versus v dd figure 11-14. pull-down resistor versus v dd figure 11-15. strong pull-up re sistor versus v dd 10.0 100.0 1000.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) r pu (k ? ) -40c 25c t amb = 105 c v il = v ss 10.0 100.0 1000.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) r pd (k ? ) -40c 25c t amb = 105 c v ih = v ss 10.0 100.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) r spu (k ? ) -40c 25c t amb = 105 c v il = v ss
100 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 11-16. strong pull-down resistor versus v dd figure 11-17. output high current versus v dd ? output high voltage figure 11-18. output low current versus output low voltage 10.0 100.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd (v) r spd (k ? ) -40c 25c t amb = 105c v ih = v dd -40 -35 -30 -25 -20 -15 -10 -5 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v dd - v oh (v) i oh (ma) t amb = 25c v dd = 2.0 v 4.0 v 3.0 v 5.0 v 6.5 v 0 5 10 15 20 25 30 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 v ol (v) i ol (ma) t amb = 25c v dd = 6.5 v 4.0 v 3.0 v 5.0 v 2.0 v
101 4593d?4bmcu?05/06 ATAR092-C/atar892-c figure 11-19. output high current versus t amb , v dd = 6.5 v, v oh = 0.8 v dd figure 11-20. output low current versus t amb , v dd = 6.5 v, v ol = 0.2 v dd -25 -20 -15 -10 -5 0 -40 -20 0 20 40 60 80 100 120 t amb (c) i oh (ma) min. typ. max. 0 5 10 15 20 25 -40 -20 0 20 40 60 80 100 120 t amb (c) i ol (ma) max. min. typ.
102 4593d?4bmcu?05/06 ATAR092-C/atar892-c 12. emulation the basic function of emulation is to test and evaluate the customer's program and hardware in real time. this therefore enables the analysis of any timing, hardware or software problem. for emulation purposes, all marc4 controllers includ e a special emulation mode. in this mode, the internal cpu core is inactive and the i/o buses are available via port 0 and port 1 to allow an external access to the on-chip peripherals. the marc4 emulator uses this mode to control the peripherals of any marc4 controller (target chip) and emulates the lost ports for the application. the marc4 emulator can stop and restart a program at specified points during execution, mak- ing it possible for the applications engineer to view the memory contents and those of various registers during program executio n. the designer also gains th e ability to analyze the executed instruction sequences and all the i/o activities. figure 12-1. marc4 emulation marc4 target chip core (inactive) p o r t 1 p o r t 0 application-specific hardware peripherals marc4 emulator program memory trace memory control logic personal computer core marc4 emulation-cpu i/o control i/o bus port 0 port 1 syscl/ tcl, te, nrst emulation control emulator target board
103 4593d?4bmcu?05/06 ATAR092-C/atar892-c please attach this page to the approval form. filename: ___________________________ .hex crc: ___________________________ (hex) date: ____________ signature: _________________________ company: _________________________ notes: 1. it is required to select an output option for each po rt pin (port 1, port 2, port 4, port 5, port 6). 2. don?t use external components at bp20 that pull to v ss during reset representing a resistor < 150k. 13. option settings for ordering [ ] ATAR092-C (-40c to +105c) [ ] atar892-c (-40c to +105c) please select the option settings from the list below and insert rom crc. output (1) input output input port 1 port 5 bp10 [ ] cmos [ ] switched pull-up bp50 [ ] cmos [ ] switched pull-up [ ] open drain [n] [ ] switched pull-down [ ] open drain [n] [ ] switched pull-down [ ] open drain [p] [ ] static pull-up [ ] open drain [p] [ ] static pull-up [ ] static pull-down [ ] static pull-down bp13 [ ] cmos [ ] switched pull-up bp51 [ ] cmos [ ] switched pull-up [ ] open drain [n] [ ] switched pull-down [ ] open drain [n] [ ] switched pull-down [ ] open drain [p] [ ] static pull-up [ ] open drain [p] [ ] static pull-up [ ] static pull-down [ ] static pull-down port 2 bp52 [ ] cmos [ ] switched pull-up bp20 (2) [ ] cmos [ ] switched pull-up [ ] open drain [n] [ ] switched pull-down [ ] open drain [n] [ ] switched pull-down [ ] open drain [p] [ ] static pull-up [ ] open drain [p] [ ] static pull-up [ ] static pull-down [ ] static pull-down bp53 [ ] cmos [ ] switched pull-up bp21 [ ] cmos [ ] switched pull-up [ ] open drain [n] [ ] switched pull-down [ ] open drain [n] [ ] switched pull-down [ ] open drain [p] [ ] static pull-up [ ] open drain [p] [ ] static pull-up [ ] static pull-down [ ] static pull-down port 6 bp22 [ ] cmos [ ] switched pull-up bp60 [ ] cmos [ ] switched pull-up [ ] open drain [n] [ ] switched pull-down [ ] open drain [n] [ ] switched pull-down [ ] open drain [p] [ ] static pull-up [ ] open drain [p] [ ] static pull-up [ ] static pull-down [ ] static pull-down bp23 [ ] cmos [ ] switched pull-up bp63 [ ] cmos [ ] switched pull-up [ ] open drain [n] [ ] switched pull-down [ ] open drain [n] [ ] switched pull-down [ ] open drain [p] [ ] static pull-up [ ] open drain [p] [ ] static pull-up [ ] static pull-down [ ] static pull-down port 4 bp40 [ ] cmos [ ] switched pull-up osc1 [ ] open drain [n] [ ] switched pull-down [ ] no integrated capacitance [ ] open drain [p] [ ] static pull-up [ ] inter nal capacitance (0 to 20 pf) [ _____pf] [ ] static pull-down osc2 bp41 [ ] cmos [ ] switched pull-up [ ] no integrated capacitance [ ] open drain [n] [ ] switched pull-down [ ] internal capacitance (0 to 20 pf) [ _____pf] [ ] open drain [p] [ ] static pull-up [ ] static pull-down clock used [ ] external resistor bp42 [ ] cmos [ ] switched pull-up [ ] external clock osc1 [ ] open drain [n] [ ] switched pull-down [ ] external clock osc2 [ ] open drain [p] [ ] static pull-up [ ] 32-khz crystal [ ] static pull-down [ ] 4-mhz crystal bp43 [ ] cmos [ ] switched pull-up [ ] open drain [n] [ ] switched pull-down ecm (external clock monitor) [ ] open drain [p] [ ] static pull-up [ ] enable [ ] static pull-down [ ] disable
104 4593d?4bmcu?05/06 ATAR092-C/atar892-c 15. package information 14. ordering information extended type number program memory data-eeprom package delivery atar092x-yyy-tkqyz 4 kb rom no sso20 taped and reeled atar092x-yyy-tksyz 4 kb rom no sso20 tubes atar892x-yyy-tkqyz 4 kb rom 512 bit sso20 taped and reeled atar892x-yyy-tksyz 4 kb rom 512 bit sso20 tubes note: x = hardware revision yyy = customer specific rom-version z = operating temperature range = c (-40c to +105c) y = lead-free technical drawings according to din specifications package sso20 dimensions in mm 6.75 6.50 0.25 0.65 5.85 1.30 0.15 0.05 5.7 5.3 4.5 4.3 6.6 6.3 0.15 20 11 110
105 4593d?4bmcu?05/06 ATAR092-C/atar892-c 16. revision history please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. revision no. history 4593d-4bmcu-05/06 ? put datasheet in a new template ? lead-free logo on page 1 deleted ? section 14 ?ordering information? on page 104 changed 4593c-4bmcu-12/04 ? put datasheet in a new template ? lead-free logo on page 1 added ? section ?rom? on page 4 changed ? section ?interrupt proces sing? on pages 7-8 changed ? section ?4-mhz? oscillator on pages 16-17 changed ? section ?32-khz oscillator? on page 17 changed ? table ?ac characteristics? on pages 85-86 changed ? table ?option settings for ordering? on page 95 changed ? table ?ordering information? on page 96 changed 4593b-4bmcu-03/04 ? put datasheet in a new template ? features on page 1 changed ? table 1 ?available variants of ataxx9x? changed ? table 10 ?pheripheral addresses? on page 21 changed ? section ?timer 2? on page 33 changed ? table 20 ?timer 2 output select bits? on page 42 changed ? figure 44 on page 44 changed ? section ?eeprom ? operating modes? on page 80 changed ? new heading rows at table ?absolute maximum ratings? on page 83 added ? system clock cycle in table ?ac characteristics? on page 85 changed ? section ?emulation? on page 94 added ? table name on page 95 changed ? table ?ordering information? on page 96 added
106 4593d?4bmcu?05/06 ATAR092-C/atar892-c 17. table of contents features ................ ................ .............. ............... .............. .............. ............ 1 1 description ............ .............. .............. ............... .............. .............. ............ 1 2 pin configuration ..... ................ ................ ................. ................ ............... 2 3 introduction .............. ................ ................ ................. ................ ............... 3 4 marc4 architecture .............. .............. .............. .............. .............. .......... 3 4.1 general description .............................................................................................3 4.2 components of marc4 core ..............................................................................4 4.2.1 rom ................................................................................................................4 4.2.2 ram ................................................................................................................4 4.2.3 registers .........................................................................................................5 4.2.4 alu .................................................................................................................7 4.2.5 i/o bus ............................................................................................................8 4.2.6 instruction set .................................................................................................8 4.2.7 interrupt structure ...........................................................................................8 4.3 master reset ......................................................................................................10 4.3.1 power-on reset and brown-out detection ....................................................11 4.3.2 watchdog reset ...........................................................................................12 4.3.3 external clock supervisor .............................................................................12 4.4 voltage monitor ..................................................................................................12 4.4.1 voltage monitor control/status register .......................................................13 4.5 clock generation ...............................................................................................14 4.5.1 clock module ................................................................................................14 4.5.2 oscillator circuits and external clock input stage .......................................16 4.5.3 clock management .......................................................................................19 4.6 power-down modes ...........................................................................................20 5 peripheral modules ............. .............. ............... .............. .............. .......... 21 5.1 addressing peripherals ......................................................................................21 5.2 bi-directional ports .............................................................................................23 5.2.1 bi-directional port 1 .......................................................................................23 5.2.2 bi-directional port 2 .......................................................................................24 5.2.3 bi-directional port 5 .......................................................................................26 5.2.4 bi-directional port 4 .......................................................................................28 5.2.5 bi-directional port 6 .......................................................................................30 5.3 universal timer/counter/ communication module (utcm) ...............................31 5.3.1 timer 1 ..........................................................................................................32 5.3.2 timer 2 ..........................................................................................................35 5.3.3 timer 3 ..........................................................................................................47
107 4593d?4bmcu?05/06 ATAR092-C/atar892-c 5.3.4 synchronous serial interface (ssi) ...............................................................62 5.3.5 combination modes ......................................................................................73 6 atar892-c ............ .............. .............. ............... .............. .............. .......... 84 6.1 internal 2-wire multi-chip link ............................................................................84 6.2 u505m eeprom ...............................................................................................85 6.2.1 serial interface ..............................................................................................85 6.2.2 eeprom ............ ................ ................ ................ ................ ................ ..........87 7 absolute maximum ratings .... ................ ................. ................ ............. 90 8 thermal resistance ............ .............. ............... .............. .............. .......... 90 9 dc operating characteristics ................. ................. ................ ............. 90 10 ac characteristics ..... ................ ................. ................ ................. .......... 92 11 diagrams ................ .............. .............. ............... .............. .............. .......... 95 12 emulation ............. .............. .............. .............. .............. .............. ........... 102 13 option settings for ordering ................ ................. ................ ............. 103 14 ordering information .......... .............. ............... .............. .............. ........ 104 15 package information .......... .............. ............... .............. .............. ........ 104 16 revision history ....... ................ ................ ................. ................ ........... 105
disclaimer: the information in this document is provided in connection with atmel products. no license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of atmel products. except as set forth in atmel?s terms and condi- tions of sale located on atmel? s web site, atmel assumes no liability whatsoever and disclaims any express, implied or statutor y warranty relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particu lar purpose, or non-infringement. in no event shall atmel be liable for any direct, indirect, conseque ntial, punitive, special or i nciden- tal damages (including, without limitation, damages for loss of profits, business interruption, or loss of information) arising out of the use or inability to use this document, even if at mel has been advised of the possibility of such damages. atmel makes no representations or warranties with respect to the accuracy or co mpleteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. atmel does not make any commitment to update the information contained her ein. unless specifically provided otherwise, atmel products are not suitable for, and shall not be used in, automotive applications. atmel?s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. atmel corporation atmel operations 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 487-2600 regional headquarters europe atmel sarl route des arsenaux 41 case postale 80 ch-1705 fribourg switzerland tel: (41) 26-426-5555 fax: (41) 26-426-5500 asia room 1219 chinachem golden plaza 77 mody road tsimshatsui east kowloon hong kong tel: (852) 2721-9778 fax: (852) 2722-1369 japan 9f, tonetsu shinkawa bldg. 1-24-8 shinkawa chuo-ku, tokyo 104-0033 japan tel: (81) 3-3523-3551 fax: (81) 3-3523-7581 memory 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 microcontrollers 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 la chantrerie bp 70602 44306 nantes cedex 3, france tel: (33) 2-40-18-18-18 fax: (33) 2-40-18-19-60 asic/assp/smart cards zone industrielle 13106 rousset cedex, france tel: (33) 4-42-53-60-00 fax: (33) 4-42-53-60-01 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 scottish enterprise technology park maxwell building east kilbride g75 0qr, scotland tel: (44) 1355-803-000 fax: (44) 1355-242-743 rf/automotive theresienstrasse 2 postfach 3535 74025 heilbronn, germany tel: (49) 71-31-67-0 fax: (49) 71-31-67-2340 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 biometrics/imaging/hi-rel mpu/ high-speed converters/rf datacom avenue de rochepleine bp 123 38521 saint-egreve cedex, france tel: (33) 4-76-58-30-00 fax: (33) 4-76-58-34-80 literature requests www.atmel.com/literature 4593d?4bmcu?05/06 ? 2006 atmel corporation . all rights reserved. atmel ? , logo and combinations thereof, everywhere you are ? and others are registered trade- marks or trademarks of atmel corporation or its subsidiari es. other terms and product names may be trademarks of others.

▲Up To Search▲

Price & Availability of ATAR092-C

	To Download ATAR092-C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .